White Outdoor 850W, 1150W manual Off-season Storage

Page 14

Drive

Cover

Screw

Left Axle

Left Drive

Cover

Figure 16

Holding the friction wheel assembly, slide the hex shaft out of the left side of the frame. The spacer on the right side of the hex shaft will fall and the sprocket should remain hanging loose in the chain. See Figure 17.

 

Shift Rod

 

Assembly

Gear Shaft

 

 

Pin

 

Sprocket

 

Friction

Drive Shaft

Wheel

 

Assembly

Figure 17

Lift the friction wheel assembly out between the axle shaft and the drive shaft assemblies.

Remove the six screws from the friction wheel assembly (three from each side). Remove the friction wheel rubber from between the friction wheel plates. See Figure 18.

Screws

Friction Wheel Rubber

Hub

Screws

Friction Wheel

Plates

Figure 18

Reassemble the new friction wheel rubber to the friction wheel plates and hub, tightening the six screws in rotation and with equal force.

Position the friction wheel assembly up onto the pin of the shift rod assembly, and slide the hex shaft through the friction wheel assembly. Reassemble in reverse order.

Off-season Storage

WARNING: Never store the machine or fuel container indoors where there is an open flame, spark, or pilot light such as on water heater, furnace, clothes dryer, or other gas appliance.

WARNING: Drain fuel into an approved container outdoors, away from an open flame. Allow engine to cool. Extinguish cigarettes, cigars, pipes, and other sources of ignition prior to draining fuel. Fuel left in engine for extended periods deteriorates and will cause starting problems.

If unit is to be stored over 30 days, prepare for storage as follows:

Remove gasoline from carburetor and fuel tank to prevent gum deposits from forming on these parts and causing possible malfunction of engine.

Run engine until fuel tank is empty and engine stops due to lack of fuel.

Drain carburetor by pressing upward on bowl drain, located below the carburetor cover.

NOTE: Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Do not drain carburetor if using fuel stabilizer.

Wipe equipment with an oiled rag to prevent rust.

Remove spark plug and pour one ounce of engine oil through spark plug hole into cylinder. Cover spark plug hole with rag. Crank engine several times to distribute oil. Replace spark plug.

Follow the lubrication recommendations found in the Maintenance Section.

Always store the snow thrower in a clean, dry area.

NOTE: When storing any type of power equipment in an unventilated or metal storage shed, care should be taken to rust proof the equipment. Using a light oil or silicone, coat the equipment, especially any chains, springs, bearings and cables.

14

Image 14
Contents OPERATOR’S Manual Table of Contents Preparation Important Safe Operation PracticesTraining OperationMaintenance And Storage Your ResponsibilityUnpacking AssemblyAssembling Your Snow Thrower Loose PartsSkid Shoe Adjustment Final AdjustmentsAuger Control Adjustment Traction Control and Shift Lever AdjustmentAuger Drive Control Know Your Snow ThrowerChute Tilt Control Skid ShoeOperating Your Snow Thrower To Engage Wheel Drive Recoil StarterTo Stop Engine To Engage AugersShift Rod Adjustment Chute Assembly AdjustmentTraction Control Adjustment Maintaining Your Snow Thrower Skid Shoe AdjustmentAuger Control Adjustment Drive WheelsEngine Belt Removal And ReplacementServicing Your Snow Thrower AugersReplacing Friction Wheel Rubber Drive BeltOff-season Storage Trouble Shooting Problem Cause RemedyPage Models 850W & 1150W Part DescriptionModels 850W / 1150W 736-0159 Washer Models 850W / 1150W Carriage Bolt, 5/16-18 x Models 850W / 1150W Models 850W / 1150W Models 850W / 1150W 784-5590 Page Page MANUFACTURER’S Limited Warranty for

850W, 1150W specifications

The White Outdoor 1150W and 850W models represent a line of powerful and reliable outdoor equipment tailored for both professional and residential use. Renowned for their exceptional performance, these machines are equipped with advanced technologies that make them suitable for various outdoor tasks, including snow removal, leaf blowing, and lawn care.

One of the standout features of the White Outdoor 1150W is its robust 1150-watt motor. This motor provides ample power to tackle heavy-duty tasks without compromising efficiency. The design of the motor allows for optimal airflow, ensuring that the machine operates smoothly even under demanding conditions. Similarly, the 850W model, while slightly less powerful, is still equipped with an efficient 850-watt motor that delivers strong performance for everyday outdoor chores.

Both models boast user-friendly designs, emphasizing comfort and ease of use. The ergonomic handles are designed to reduce fatigue during extended use, making them ideal for those who may spend long hours working outdoors. The lightweight structure of both units enhances maneuverability, allowing users to navigate tight spaces and carry the machines effortlessly.

Another significant characteristic of the White Outdoor series is their versatile functionality. The 1150W model often features multiple speed settings, enabling users to adjust the power output according to the task at hand. This adaptability makes it perfect for various applications, from gentle blowing for delicate flowers to powerful blasts for clearing heavy debris. The 850W model, while simpler, still offers dependable performance for standard clean-up jobs.

Safety is a paramount consideration in these designs. Both models include features such as thermal overload protection, which prevents the motors from overheating during prolonged use. Additionally, the machines are built with durable materials that withstand harsh weather conditions, ensuring longevity and reliability.

In terms of technology, both the 1150W and 850W benefit from energy-efficient engineering that not only saves power but also minimizes environmental impact. This is linked to an emphasis on creating machines that balance performance with sustainability.

In conclusion, the White Outdoor 1150W and 850W models are excellent choices for anyone looking to enhance their outdoor maintenance capabilities. With powerful motors, user-friendly designs, versatile functionality, and a focus on safety and sustainability, these machines stand out as reliable tools for accomplishing a wide range of outdoor tasks.