Yard-Man E663H Operating Your Snow Thrower, Before Starting Gas And Oil Fill-up, Starting Engine

Page 8

Traction/Auger

 

Shift Lever

Chute Tilt

 

Control Lock

 

 

 

 

Control

Fuel Shut-Off Valve

 

 

 

 

 

 

(If So Equipped)

 

 

 

 

 

Auger Control

 

Discharge Chute

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Chute

 

 

 

 

Chute Directional

 

Clean-Out Tool

 

 

 

 

 

 

 

 

 

Control

 

 

 

 

 

 

 

 

 

 

 

 

Choke

Closed

Open

Primer

Auger

Ignition Key

Rope

Starter

Throttle Control

Handle

Figure 6

SECTION 5: OPERATING YOUR SNOW THROWER

Before Starting

WARNING: Read, understand, and follow all instructions and warnings on the machine and in this manual before operating.

Gas And Oil Fill-up

Check oil level and add oil if necessary. Service the engine with gasoline as instructed in the separate engine manual packed with your snow thrower.

WARNING: Use extreme care when handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Never fuel the machine indoors or while the engine is hot or running. Extinguish cigarettes, cigars, pipes and other sources of ignition.

Starting Engine

IMPORTANT: Prior to operating your snow thrower, read, understand and follow ALL instructions to perform adjustments found under the heading Auger Control Test on page 9 of this manual.

Attach spark plug wire to spark plug. Make certain the metal loop on end of the spark plug wire (inside

the boot) is fastened securely over the metal tip on the spark plug.

Make certain the fuel cut-off valve, if your snow thrower is so equipped, is in OPEN position.

Make certain the auger and drive clutch levers are in the disengaged (released) position.

Move throttle control to FAST (Rabbit) position. Insert ignition key into slot. Be certain it snaps into place. Do not turn key.

NOTE: Engine will not start unless ignition key is inserted into ignition slot in carburetor cover.

Electric Starter

Determine that your house wiring is a three-wire grounded system. Ask a licensed electrician if you are not certain.

If your house wiring system is not a three-wire grounded system, do not use this electric starter under any conditions.

WARNING: The electric starter is equipped with a grounded three-wire power cord and plug and is designed to operate on 120 volt AC household current. It must be used with a properly grounded three-prong receptacle at all times to avoid the possibility of electric shock. Follow all instructions carefully prior to operating the electric starter.

8

Image 8 Contents
Operator’s Manual Table of Contents Important Safe Operation Practices Training Maintenance and Storage Loose Parts Assembling Your Snow ThrowerChute Clean-Out Tool Final AdjustmentsTraction Control and Shift Lever Adjustment Tire Pressure AdjustmentKnow Your Snow Thrower Operating Your Snow Thrower Before Starting Gas And Oil Fill-upStarting Engine Electric StarterTo Engage Augers To Stop EngineTo Engage Drive Drift Cutters if so equipped Chute Assembly Adjustment Chute Directional Control Support Bracket AdjustmentTraction Control Adjustment Operating TipsShift Rod Adjustment Auger Control AdjustmentSkid Shoes Drive WheelsService Maintaining Your Snow ThrowerLubrication AugersBelt Removal And Replacement Shave Plate and Skid ShoesAuger Belt Drive BeltServicing Friction Wheel Rubber Off-season Storage Troubleshooting Problem Cause RemedyModel E663H & E643E Parts List Models E663H & E643E Part Description3132 Models E663H & E643E Models E663H & E643E 748-0360 Pulley 26 -0654A Hex Washer Screw 3/8-16 x 629-0071 64 a B 746-0896 Models E663H & E643E Page MANUFACTURER’S Limited Warranty for MTD LLC, P.O. BOX 361131 CLEVELAND, Ohio 44136-0019 Phone