Yard-Man 769-03245 warranty Drive Belt Replacement, Remove and replace belt in the reverse order

Page 18

6

Maintaining

Your Snow

Thrower

Figure 6-9

Augers

The augers are secured to the spiral shaft with two shear pins and cotter pins. If the auger should strike a foreign object or ice jam, the snow thrower is designed so that the pins may shear. Refer to Figure 6-9.

If the augers will not turn, check to see if the pins have sheared. One set of replacement shear pins has been provided with the snow thrower. When replacing pins, spray an oil lubricant into shaft before inserting new pins.

Drive Belt Replacement

To remove and replace your snow thrower’s auger belt, proceed as follows:

1.Remove the plastic belt cover on the front of the engine by removing the two self-tapping screws. See Figure 6-9.

NEVER replace the auger shear pins with standard hex pins. Any damage to the auger gearbox or other components as a result of failing to do so will NOT be covered by your snow thrower’s warranty.

c

Figure 6-10

b

Drain the gasoline from the snow thrower, or place a piece of plastic under the gas cap.

Carefully pivot the snow thrower up and forward so that it rests on the auger housing. See Figure 6-10.

2.Remove the frame cover from the underside of the snow thrower by removing four self-tapping screws which secure it.

3.a. Use a wrench to pivot the idler pulley toward the right. See Figure 6-11.

b.Roll the auger belt off the engine pulley.

c.Lift the drive belt off engine pulley.

4.Slip the drive belt off the pulley and between friction wheel and friction wheel disc. See Figure 6-12.

• Remove and replace belt in the reverse order.

a

Figure 6-11

Figure 6-12

18

Image 18
Contents Two-Stage Snow Thrower 769-0324506/05/07 Table of Contents Finding and Recording Model NumberCustomer Support Chute Clean-out Tool Your Responsibility Restrict the usePreparation Safe Operation PracticesTraining Your ResponsibilityDo not modify engine Maintenance & StorageOperation Average Useful LifeSetting Up Setting Up Your Snow Thrower Shear Pin Storage optionalDrift Cutters If Equipped Snowthrower ModelAll models Skid Shoes Clean-Out ToolLamp Wiring Harness If equipped Tire Pressure Pneumatic TiresOperating Your Snow Thrower Know Your Snow Thrower$26% #/.42 Gas & Oil Fill-Up Stopping The EngineElectric Starter If Equipped Recoil Starter To Engage DriveTo Engage Augers Auger Control TestChute Control Making AdjustmentsShift Cable Drive Control & Shift LeverReversible Plastic Skid Shoe Reversible Steel Skid ShoeLubrication Maintaining Your Snow ThrowerEngine Shave Plate and Skid ShoesAuger Belt Replacement Roll the auger belt off the engine pulley. See FigureUnhook the support bracket spring from the frame Drive Belt Replacement Remove and replace belt in the reverse orderFriction Wheel Removal Remove the rubber ring from between the platesOff-Season Storage Wipe equipment with an oiled rag to prevent rustTrouble Shooting Problem Cause RemedyWarranty 12.08.06Auger Housing COMPONENTS/COMPOSANTS DU Logement DES Tarières Manual Chute Control Part Description RÉF Pièce Optional/en option Part Description RÉF Pièce 30 in/po Remarque Lhabitacle peut être légèrement différentPart Description RÉF Pièce 31AE6GKF500 Part For parts and/or accessories refer to customer support on For parts and/or accessories refer to customer support on Page Garantie FrottementSolution Causes Problème DépannagePropre et SouffleuseCarburant le Videz Gaz ’entretien Régime De courroie la de Remplacement TransmissionTarières ’entretien RégimePatins et plate Lame LubrificationMoteur Patins Tarière la de CommandeRéglages Plastique en réversible Patins 4-5 FigureVitesses de levier Et transmission la de CommandeGoulotte la de Commande Vitesses de changement de CâbleToucher SouffleuseMain 150F dépasserModèles ’huile et d’essence PleinsModèles certains sur électrique Démarreur Certains sur électrique DémarreurLa de proximité à Trans de commande la de BlocageTarières Souffleuse laSouffleuse la de Commandes Départ de Volet’essence plein le jamais faites Ne Pneumatiques Bandages pneus des Pression Général d’ordre RecommandationsGoulotte la de dégagement de Outil Goulotte la de dégagement de OutilÉchéant cas le coupe de Barres Option en cisaillement de goupille la de Remisage Quant moteur du d’utilisation notice la consulter veuillez InférieurEmployer à moteur à l’huile à et carburant au ’assemblage Après .ESSENCE Sans mais d’huile pleinMoyenne utile vie de Durée Remisage et EntretienResponsabilité Votre Gaz de émissions les concernant AvisFormation UtilisationPréparation Responsabilité VotreEst goulotte la de dégagement de outil Un De OutilMatières des Table Vente-après ServiceModèle de numéro le trouver Pour ’utilisation La voir détachées PiècesPhases deux neige à Souffleuse 06/05/07 03245-769