Yard-Man 769-03245 warranty Friction Wheel Removal, Remove the rubber ring from between the plates

Page 19

Figure 6-13

Figure 6-14

Figure 6-15

Friction Wheel Removal

If the snow thrower fails to drive with the drive control engaged, and performing the drive control cable adjust- ment on page 12 fails to correct the problem, the friction wheel may need to be replaced. Follow the instructions below. Examine the friction wheel for signs of wear or cracking and replace if necessary.

Place the shift lever in third Forward (F3) position.

Drain the gasoline from the snow thrower, or place a piece of plastic under the gas cap.

Carefully pivot the snow thrower up and forward so that it rests on the auger housing.

1.a. Remove the frame cover from the underside of the snow thrower by removing four self-tapping screws which secure it. See Figure 6-13.

b.Remove the right-hand wheel by removing the screw and cupped washer which secure it to the axle.

2.Carefully remove the hex nut and washer which secures the hex shaft to the snow thrower frame and lightly tap the shaft’s end to dislodge the ball bearing from the right side of the frame. See Figure 6-14.

3.Carefully position the hex shaft downward and to the left before carefully sliding the friction wheel assembly off the shaft. See Figure 6-15.

NOTE: If you’re replacing the friction wheel assembly as a whole, discard the worn part and slide the new part onto the hex shaft. Follow the steps above in reverse order to reassemble components. If you’re disassem- bling the friction wheel and replacing only the rubber ring, proceed as follows:

4.Remove the four screws which secure the friction wheel’s side plates together. See Figure 6-16.

Remove the rubber ring from between the plates.

Reassemble the side plates with a new rubber ring.

Slide the friction wheel assembly back onto the hex shaft and follow the steps above in reverse order to reassemble components.

Figure 6-16

6

Maintaining

Your Snow

Thrower

When reassembling the friction wheel as- sembly, tighten each screw only one rota- tion before turning the wheel clockwise and proceeding with the next screw. Repeat this process several times to ensure the plates are secured with equal force.

NEVER replace the auger shear pins with standard hex pins. Any damage to the auger gearbox or other components as a result of failing to do so will NOT be covered by your snow thrower’s warranty.

19

Image 19
Contents 769-03245 Two-Stage Snow Thrower06/05/07 Finding and Recording Model Number Table of ContentsCustomer Support Your Responsibility Restrict the use Chute Clean-out ToolYour Responsibility Safe Operation PracticesTraining PreparationAverage Useful Life Maintenance & StorageOperation Do not modify engineSetting Up Shear Pin Storage optional Setting Up Your Snow ThrowerSnowthrower Model Drift Cutters If EquippedAll models Tire Pressure Pneumatic Tires Clean-Out ToolLamp Wiring Harness If equipped Skid ShoesKnow Your Snow Thrower Operating Your Snow Thrower$26% #/.42 Stopping The Engine Gas & Oil Fill-UpElectric Starter If Equipped Auger Control Test To Engage DriveTo Engage Augers Recoil StarterDrive Control & Shift Lever Making AdjustmentsShift Cable Chute ControlReversible Steel Skid Shoe Reversible Plastic Skid ShoeShave Plate and Skid Shoes Maintaining Your Snow ThrowerEngine LubricationRoll the auger belt off the engine pulley. See Figure Auger Belt ReplacementUnhook the support bracket spring from the frame Remove and replace belt in the reverse order Drive Belt ReplacementRemove the rubber ring from between the plates Friction Wheel RemovalWipe equipment with an oiled rag to prevent rust Off-Season StorageProblem Cause Remedy Trouble Shooting12.08.06 WarrantyAuger Housing COMPONENTS/COMPOSANTS DU Logement DES Tarières Manual Chute Control Part Description RÉF Pièce Optional/en option Part Description RÉF Pièce Remarque Lhabitacle peut être légèrement différent 30 in/poPart Description RÉF Pièce 31AE6GKF500 Part For parts and/or accessories refer to customer support on For parts and/or accessories refer to customer support on Page Frottement GarantieDépannage Solution Causes ProblèmeSouffleuse Propre etCarburant le Videz Gaz ’entretien Régime Transmission De courroie la de RemplacementTarières Régime ’entretienLubrification Patins et plate LameMoteur Plastique en réversible Patins 4-5 Figure Tarière la de CommandeRéglages PatinsVitesses de changement de Câble Et transmission la de CommandeGoulotte la de Commande Vitesses de levier150F dépasser SouffleuseMain ToucherCertains sur électrique Démarreur ’huile et d’essence PleinsModèles certains sur électrique Démarreur ModèlesSouffleuse la Trans de commande la de BlocageTarières La de proximité àDépart de Volet Souffleuse la de Commandes’essence plein le jamais faites Ne Goulotte la de dégagement de Outil Général d’ordre RecommandationsGoulotte la de dégagement de Outil Pneumatiques Bandages pneus des PressionÉchéant cas le coupe de Barres Option en cisaillement de goupille la de Remisage ’assemblage Après .ESSENCE Sans mais d’huile plein InférieurEmployer à moteur à l’huile à et carburant au Quant moteur du d’utilisation notice la consulter veuillezGaz de émissions les concernant Avis Remisage et EntretienResponsabilité Votre Moyenne utile vie de DuréeResponsabilité Votre UtilisationPréparation FormationDe Outil Est goulotte la de dégagement de outil Un’utilisation La voir détachées Pièces Vente-après ServiceModèle de numéro le trouver Pour Matières des Table06/05/07 03245-769 Phases deux neige à Souffleuse