Yard-Man 31AE553F401, 31AE573H401 Operation, GAS and OIL FILL-UP, To Start Engine, To Stop Engine

Page 9

SECTION 7: OPERATION

GAS AND OIL FILL-UP

Service the engine with gasoline and oil as instructed in the separate engine manual packed with your snow thrower. Read instructions carefully.

WARNING: Never fill fuel tank indoors, with engine running or while engine is hot. Do not smoke when filling fuel tank.

Electric Starter

WARNING: The electric starter is equipped with a three-wire power cord and plug, and is designed to operate on 120 volt AC household current. It must be properly grounded at all times to avoid possibility of electric shock which may be injurious to the operator. Follow all instructions carefully. Determine that your house wiring is a three-wire grounded system. Ask a licensed electrician if you are not certain. If your house wiring system is not a three- wire grounded system, do not use this electric starter under any conditions. If your house wiring system is grounded but a three-hole receptacle is not available at the point the starter will normally be used, one should be installed by a licensed electrician.

When connecting the power cord, always connect cord to starter on engine first, then plug the other end into a three-hole grounded receptacle.

When disconnecting the power cord, always unplug the end from the three-hole grounded receptacle first.

TO START ENGINE

(See Figure 11)

IMPORTANT: If unit shows any sign of motion (drive or augers) with the clutch grips disengaged, shut engine off immediately. Readjust as instructed in the “Final Adjustments” section of the Set-Up Instructions.

1.Attach spark plug wire to spark plug. Make certain that the metal loop on the end of the spark plug wire (inside the boot) is fastened securely over the metal tip on the spark plug.

2.Make certain the fuel shut-off valve is in the open (vertical) position.

3.Make certain the auger and drive clutch levers are in the disengaged (released) position.

4.Move throttle control to FAST position.

5.Insert ignition key into slot. Make sure it snaps

into place. Do not turn key.

Follow the next three steps in the case of electric start only.

6.Rotate choke knob to OFF position.

7.Push the primer button while covering the vent hole. Remove finger from the primer between primes. Do not prime to start a warm engine. Prime two to three times at temperature above 15 degree F and four times below 15 degree F.

8.Connect power cord to switch box on engine. Plug the other end of power cord into a three- hole, grounded 120 volt AC receptacle.

9.Push starter button to crank the engine. When engine starts, release the starter button, and move choke gradually to FULL, and then to OFF position. If the engine falters, move choke immediately to FULL position and then gradually

move it to OFF position.

Follow the next three steps for recoil start only:

10.Rotate choke knob to FULL position. If engine is already warm, place choke in OFF position instead of FULL position.

11.Push primer button two or three times. If engine is warm, push primer button once only.

12.Grasp starter handle and pull rope out slowly, until it pulls slightly harder. Let rope rewind slowly. Pull starter handle rapidly. Do not allow handle to snap back. Allow it to rewind slowly while keeping a firm hold on the starter handle. Repeat until engine starts. As engine warms up and begins to operate evenly, rotate choke knob slowly to OFF position. If engine falters, return to FULL choke, then slowly move to OFF position.

Push starter button

Insert

 

Prime

Attach spark

key

 

 

plug

 

 

Rotate

Connect to

electric

choke

cord

Move throttle

Pull rope

control

Figure 11

TO STOP ENGINE

1.Run engine for a few minutes before stopping to help dry off any moisture on the engine.

9

Image 9
Contents MTD Products INC. P.O. BOX 368022 CLEVELAND, Ohio Important Read Safety Rules and Instructions CarefullyTraining Important Safe Operation PracticesPreparation OperationSafety Labels found on your unit Maintenance and StorageFinding Snow Thrower Model Number Calling Customer SupportUnpacking the Snow Thrower SET-UP Instructions Auger Drive Clutch Final AdjustmentsSkid Shoe Traction Drive Clutch and Shift LeverControls GAS and OIL FILL-UP OperationTo Start Engine To Stop EngineTo Steer Snowthrower To Engage DriveTo Engage Augers Tire PressureAdjustments Lubrication Augers MaintenanceShave Plate and Skid Shoes Replacing BeltAuger drive belt from the front auger pulley Drive Belt Changing Friction Wheel RubberOFF-SEASON Storage Trouble Possible Causes Corrective Action Trouble Shooting GuideRepair Parts Ref. No Codes below. Please add the applicable color code Cable Guide Page 151 2732 Yard-Man Green Yard-Man Yellow0674 Powder Black Wheel Assembly Yard-Man Green Yard-Man Yellow 0674 Powder Black 0637 Tire Chain Part Number Optional PartsOther Warranties MANUFACTURER’S Limited Warranty for

31AE553F401, 31AE573H401 specifications

The Yard-Man 31AE573H401 and 31AE553F401 are two exceptional garden tractors designed to cater to the needs of homeowners and gardening enthusiasts alike. These machines combine powerful performance with innovative features to make lawn care and maintenance a breeze.

One of the standout characteristics of both models is their robust engine performance. The Yard-Man 31AE573H401 is equipped with a reliable 500cc engine, while the 31AE553F401 comes with a slightly smaller yet powerful engine. This ensures that users have the horsepower necessary to tackle tough mowing tasks and maintain even large properties efficiently. With electric start options available, both models ensure a hassle-free start-up, eliminating the stress of manual pulls.

A defining feature of these tractors is their versatile cutting systems. Both the 31AE573H401 and the 31AE553F401 feature a durable 42-inch cutting deck, designed to deliver clean and precise cuts with different height adjustments, allowing users to customize their lawn's appearance. The cutting deck design enhances maneuverability, enabling users to navigate around obstacles such as trees and flower beds while maintaining an even cut.

User comfort is a significant consideration in both models. They come with a comfortable, high-back seat that provides ample support during longer mowing sessions, reducing fatigue. The ergonomic controls are conveniently placed, ensuring that operators can easily adjust speed and cutting height without taking their hands off the steering wheel.

Equipped with advanced technologies, these tractors offer exceptional durability and ease of maintenance. The reinforced frame construction enhances stability and longevity, while easily accessible maintenance points simplify routine care. The onboard diagnostics notify users of potential issues before they become major problems, which enhances the overall reliability of the machines.

Additionally, both models feature a hydrostatic transmission that allows for smooth acceleration and effortless operation. This technology provides seamless control, enabling users to navigate various terrains without the need for shifting gears manually.

In summary, the Yard-Man 31AE573H401 and 31AE553F401 are top-tier garden tractors that embody reliability, comfort, and innovative features. Whether it's mowing a vast lawn or maneuvering through tight spaces, these machines make the task efficient and enjoyable. Ideal for homeowners seeking a dependable solution for lawn maintenance, these tractors are a valuable addition to any gardening equipment arsenal.