Craftsman 536.88113 IckPin Unlocked Sition, Before Starting the Engine, Check the OIL, Fill GAS

Page 14

ickPin

Unlocked

sition

Single Wheel Drive

Figure 17

NOTE: Make sure that the klick pin is in the single wheel drive position of the axle only and not through the locked position.

BEFORE STARTING THE ENGINE

1.Before you service or start the en- gine, familiarize yourself with the snow thrower. Be sure you under- stand the function and location of all controls.

2.Check the tension of clutch cable before starting the engine. See To Adjust The Control Cable para- graph in the Service & Adjust- ments section of this manual.

3.Be sure that all fasteners are tight.

4.Make sure the height adjust skids are properly adjusted. See To Ad- just Skid Height paragraph in the Service & Adjustments section of this manual.

5.Checktire pressure (14-17

pounds). Do not exceed maximum amount of pressure.

CHECK THE OIL"

NOTE: The engine was shipped from the factory filled with oil. Check the lev- el of the oil. Add oil as needed.

1.Make sure the unit is level.

NOTE: Do not check the level of the oil while the engine runs.

2.Remove the oil fill cap/dipstick. Check the oil.

3.if necessary, add oil until the oil reaches the FULL mark on the oil fill

cap/dipstick (see Figure 18). Do not add too much oil.

F-001060J

OII Fill C_t_p/Dipstick

;.._:_/ NOTE: Oil level

_'),y must be between full and Add mark

Figure18

4.Tighten the fill cap/dipstick securely each time you check the oil level,

NOTE: For extreme cold operating conditions of 0°F and below, use a par- tial synthetic 0W30 motor oil for easier starting.

NOTE: S.A.E. 5W30 motor oil may be used to make starting easier in areas where temperature is consistently 20°F. or lower.

FILL GAS:

NOTICE: ENGINES WHICH ARE

CERTIFIED TO COMPLY WITH CAL-

IFORNIA AND US EPA EMISSION

REGULATIONS FOR ULGE ENGINES: Are certified to operate on regular un- leaded gasoline. Include the following emission control system(s): EM, TWC (If so equipped). Include any user ad- justable features-therefore no other ad- justments are needed.

dicates that alcohol blended

i_ WARNING: Experiences In-

fuels (called gasohol or

those using ethanol or methanol) can attract moisture which leads to

separation and formation of acids during storage. Acidic gas can dam- age the fuel system of an engine while In storage.

NOTE: To avoid engine problems, the fuel system must be emptied before storage for 30 days or longer. Start the engine and let it run until the fuel lines and carburetor are empty, Use the car- buretor bowl drain to empty residual gasoline from the float chamber. Use fresh fuel next season. See the Stor-

age section in this manual for additional information.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents 0 ll a IJnl= LJKoLrIIii Operatorpresencecontrolunder any cir- cumstances TrainingEach symbol Control And Operating Symbols Maintenance and StorageEdl Zel Knife to cut carton t 1/2 inch wrenches Tools Required for AssemblyThrower To Remove Snow Thrower from CartonRaise the upper handle into operat To Assemble the Handleand Crank AssemblyReinstall flatwasher and adaptor Parts bag screw, flatwasher, IockTractionDrive SpringShort Assemble Snow ChutePosition Connect Remote ChutePositionspeedselectorlever as Plastic Tie Control PanelHeadlight HOW to SET the Skid HeightAll assembly instructions have been Remote Chute Control KnobCold weather Remote Chute Control Lever Push Know Your Snow ThrowerChoke Control Used to start a cold Engine To USE Wheel Lockout PIN HOW to Move Forward and BackwardTo Throw Snow To Stop Your Snow ThrowerCheck the OIL IckPin Unlocked SitionBefore Starting the Engine Fill GASCold Start To Start EngineTo Stop Engine If the starter is frozen and will not turn Warm StartFrozen Starter Pull as much rope out of the starter as possibleSnow Throwing Tips Moved immediately after if fallsGeneral Recommendations Lubrication ChartCustomer Responsibilities After Each USEAS Required Product SpecificationsSnow Thrower LUBRICATION-EVERY 25 HoursTo Change Engine OIL EngineLubrication Spark PlugTo Adjust Skid Height To Adjust Scraper BARSquare End Locknut HOW to Check and Adjust ThecablesTo Adjust Belts To Replace Belts FrameAugerRemovetheoldaugerdrivebelt. Replacetheaugerdrivebeltwith Engine PulleyHOW to Adjust or Replace the Friction Wheel Ve-m V-llOutdoors, away from fire or flame How To Replace The Friction WheelHexNut Shaft Howto Replace the Auger Shear Bolt To Adjust the CarburetorTo Adjust or Replace the Spark Plug As follows. Extra shear bolts were proTOadjust Other Line outdoors, away from fire or flameCorrection DifficultstartingCause

536.88113 specifications

The Craftsman 536.88113 is a versatile snow blower designed for homeowners who need power, reliability, and convenience during the winter months. This robust machine offers impressive features that cater to various snow removal needs, making it a favorite among those living in snowy regions.

One of the standout features of the Craftsman 536.88113 is its powerful engine. Equipped with a reliable 24-inch wide clearing path, it efficiently handles heavy snowfalls, ensuring that driveways and walkways remain clear and safe. The engine provides ample power to clear even the most stubborn snow piles, allowing users to tackle heavy-duty jobs with ease.

Another highlight of this snow blower is its self-propelling technology. This feature allows the user to adjust the speed settings according to their comfort level and the conditions of the terrain. The adjustable speed is particularly useful for navigating through different snow depths and types, providing a more personalized and efficient snow removal experience.

The Craftsman 536.88113 also incorporates the latest in snow throwing technology. Its high-performance auger system is designed to throw snow up to 30 feet away, which minimizes the chances of snow piling up behind the cleared area. This capability not only enhances performance but also increases the efficiency of the snow removal process.

Comfort and usability are prioritized in the design of this snow blower. It features an ergonomic handle with padded grips, ensuring that users can operate the machine comfortably, even during prolonged use. Additionally, the easy-to-access controls allow for flexible operation, enabling users to adjust settings quickly without breaking their stride.

Durability is a hallmark of the Craftsman brand, and the 536.88113 is no exception. Constructed with high-quality materials, this snow blower is designed to withstand the rigors of harsh winter conditions. The durable housing protects the internal components, ensuring longevity and consistent performance season after season.

In conclusion, the Craftsman 536.88113 combines power, efficiency, and comfort, making it an excellent choice for winter snow removal. Its user-friendly features, robust construction, and advanced throwing technology set it apart, ensuring homeowners are well-equipped to handle the challenges of winter weather. Whether you have a small walkway or a large driveway, this snow blower meets the needs of various tasks, delivering reliable results each time.
Top Page Image Contents