Craftsman 536.88113 Howto Replace the Auger Shear Bolt, To Adjust the Carburetor

Page 27

isengagedwithbothbearing platesandthatthewashersandre- tainingringareinstalledtheorigi-

nalpositionSeeFigure36. .

12,Fastenthebearingplatesusing

thefourboltsremovedearlier.

13.Make sure the hex shaft turns free- ly.

t 4. Check the adjustment of the friction

wheel. See "How To Adjust The

Friction Wheel" in this section.

15.Make sure the friction wheel and the

disc drive plate are free from grease or oil.

16.Install the bottom panel. See Figure 32.

17.Tighten the bottom bolts on each side of the bottom panel.

18.Install the top bolts on each side of the bottom panel.

19.Connect the spark plug wire,

HOWTO REPLACE THE AUGER SHEAR BOLT

The augers are secured to the auger shaft with special shear bolts. These shear bolts are designed to break and protect the ma- chine if an object becomes lodged in the au- ger housing. Do not use e harder bolt as the protection provided by the shear bolt will be lost.

,_ WARNING: For safety and to protect the machine, use only original equipment shear bolts.

To replace a broken shear bolt, proceed

as follows. Extra shear bolts were pro-

vided in the assembly parts bag.

1.Move the throttlecontrolto the stop position.Disengage all controls,

2.Disconnect the spark plug wire. Make sure aH moving parts have stopped.

3.Align the hole in the auger with the

hole in the auger shaft. Install the

F-0010SOJ

new shear pin and spacer. See

Figure 37.

4.Connect the spark plug wire.

/S!elar Pin

ar

_Figure 37

TO ADJUST THE CARBURETOR

If you think your carburetor needs ad- justing, see your nearest Craftsman

Store. Engine performance should not be affected at altitudes up to 7,000 feet.

For operation at higher elevations, con- tact your nearest Craftsman Store.

IMPORTANT: Never tamper with the engine governor, which is factory set for proper engine speed. Over-speeding the engine above the factory high speed setting can be dangerous. If you think the engine-governed high speed needs adjusting, contact your nearest Craftsman Store, which has the proper equipment and experience to make any necessary adjustments.

TO ADJUST OR REPLACE THE SPARK PLUG

NOTE: This spark ignition system

meets all requirements of the Canadian

Interference-Causing Equipment Regu- lations.

NOTE: This engine complies with all current Australian and New Zealand

limitations regarding electromagnetic interference.

If you have difficulty starting the snow thrower, adjust or replace the spark plug. Replace the spark plug is the electrodes are pitted or burned or if the porcelain is cracked. Follow the instruc- tions below.

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents 0 ll a IJnl= LJKoLrIIii Training Operatorpresencecontrolunder any cir- cumstancesMaintenance and Storage Each symbol Control And Operating SymbolsEdl Zel To Remove Snow Thrower from Carton Tools Required for AssemblyThrower Knife to cut carton t 1/2 inch wrenchesParts bag screw, flatwasher, Iock To Assemble the Handleand Crank AssemblyReinstall flatwasher and adaptor Raise the upper handle into operatConnect Remote Chute Assemble Snow ChutePosition TractionDrive SpringShortPlastic Tie Control Panel Positionspeedselectorlever asRemote Chute Control Knob HOW to SET the Skid HeightAll assembly instructions have been HeadlightKnow Your Snow Thrower Choke Control Used to start a cold EngineCold weather Remote Chute Control Lever Push To Stop Your Snow Thrower HOW to Move Forward and BackwardTo Throw Snow To USE Wheel Lockout PINFill GAS IckPin Unlocked SitionBefore Starting the Engine Check the OILTo Start Engine To Stop EngineCold Start Pull as much rope out of the starter as possible Warm StartFrozen Starter If the starter is frozen and will not turnMoved immediately after if falls Snow Throwing TipsAfter Each USE Lubrication ChartCustomer Responsibilities General RecommendationsLUBRICATION-EVERY 25 Hours Product SpecificationsSnow Thrower AS RequiredSpark Plug EngineLubrication To Change Engine OILTo Adjust Scraper BAR To Adjust Skid HeightHOW to Check and Adjust Thecables To Adjust BeltsSquare End Locknut FrameAuger To Replace BeltsEngine Pulley Removetheoldaugerdrivebelt. ReplacetheaugerdrivebeltwithVe-m V-ll HOW to Adjust or Replace the Friction WheelHow To Replace The Friction Wheel HexNut ShaftOutdoors, away from fire or flame As follows. Extra shear bolts were pro To Adjust the CarburetorTo Adjust or Replace the Spark Plug Howto Replace the Auger Shear BoltTOadjust Line outdoors, away from fire or flame OtherDifficultstarting CauseCorrection

536.88113 specifications

The Craftsman 536.88113 is a versatile snow blower designed for homeowners who need power, reliability, and convenience during the winter months. This robust machine offers impressive features that cater to various snow removal needs, making it a favorite among those living in snowy regions.

One of the standout features of the Craftsman 536.88113 is its powerful engine. Equipped with a reliable 24-inch wide clearing path, it efficiently handles heavy snowfalls, ensuring that driveways and walkways remain clear and safe. The engine provides ample power to clear even the most stubborn snow piles, allowing users to tackle heavy-duty jobs with ease.

Another highlight of this snow blower is its self-propelling technology. This feature allows the user to adjust the speed settings according to their comfort level and the conditions of the terrain. The adjustable speed is particularly useful for navigating through different snow depths and types, providing a more personalized and efficient snow removal experience.

The Craftsman 536.88113 also incorporates the latest in snow throwing technology. Its high-performance auger system is designed to throw snow up to 30 feet away, which minimizes the chances of snow piling up behind the cleared area. This capability not only enhances performance but also increases the efficiency of the snow removal process.

Comfort and usability are prioritized in the design of this snow blower. It features an ergonomic handle with padded grips, ensuring that users can operate the machine comfortably, even during prolonged use. Additionally, the easy-to-access controls allow for flexible operation, enabling users to adjust settings quickly without breaking their stride.

Durability is a hallmark of the Craftsman brand, and the 536.88113 is no exception. Constructed with high-quality materials, this snow blower is designed to withstand the rigors of harsh winter conditions. The durable housing protects the internal components, ensuring longevity and consistent performance season after season.

In conclusion, the Craftsman 536.88113 combines power, efficiency, and comfort, making it an excellent choice for winter snow removal. Its user-friendly features, robust construction, and advanced throwing technology set it apart, ensuring homeowners are well-equipped to handle the challenges of winter weather. Whether you have a small walkway or a large driveway, this snow blower meets the needs of various tasks, delivering reliable results each time.
Top Page Image Contents