Craftsman 486.2484 owner manual Limited Oneyear Warranty on 40 2-STAGE Snowthrower

Page 2

ACCESSORIES

 

,

2

SAFETY RULES.._.._

L..i_L_._._:

..........................

3

FULL SIZE HARDWARE

CHART

.........

:

4

CARTON CONTENT*S...

_..,_

.:.:

:

5

ASSEMBLY

 

 

5"

OPERATION

:

 

15_

MAINTENANCE

 

 

16

SERVICE AND ADJUSTMENTS

................................ 17

STORAGE

18

TROUBLESHOOTING

18

REPAIR

PARTS

ILLUSTRATION

......................... 20,22

REPAIR

PARTS

LIST

21,23

SLOPE

GUIDE

19

PARTS

ORDERING/SERVICE

BACK COVER

LIMITED ONEYEAR WARRANTY ON 40" 2-STAGE SNOWTHROWER

For one year from the date of purchase, when this snow thrower is maintained and lubricated according to the operating and maintenance instructionsin the owner'smanual, Sears will repair any defect in matedal or workmanship free ofcharge.

If this snow thrower is used for commercial or rental purposes, this warranty applies for only 90 days from the date of

purchase.

This warranty does not cover repairs necessary because of operator negligence or abuse, including the failure to maintain the equipment according to instructions contained in the owner's manual.

WARRANTY SERVICE IS AVAILABLE BY CONTACTING THE NEAREST SEARS SERVICE CENTER/DEPARTMENT IN THE UNITED STATES.

This warranty applies only while this product is in the United States.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Sears, Roebuck and Co. D/817 WA. Hoffman Estates, Chicago, IL 60179

These accessories were available when the unit was purchased. They are also available at most Sears retail outlets and service centers. Most Sears stores can order repair parts for you when you provide the model numbers of your tractor and snow thrower.

WHEi=L WEIGHT

TIRE CHAINS

DRIFT CUTTER BARS

 

 

KIT NO. 71-52050

======_

The model number and serial numbers will be found on a decal attached to the snow thrower.

You should record both the serial nLimber and the date of purchase and keep in a safe place f(_rfuture reference.

MODEL NUMBER:

486.248400

SERIAL NUMBER:

DATE OF PURCHASE:

2

Image 2
Contents CRI1FTSMI1N Limited Oneyear Warranty on 40 2-STAGE Snowthrower Tire Chains Drift Cutter BarsBecome alert!! Your safety is involved Hairpin Cotter QTY DescriptionBolt, 1/2 x 1-1/4 Hex Lock Nut HairpinCarton Contents Tractor Preparation Tools Required for AssemblyRemoval of Parts from Carton Bolt Removed Washer From this HEX Lock NUTSide Plate 8SHOULDER Bolt Lock NUTHairpin COI-rER Hairpin Cotter Pivot Lock PIN ROD Right Side ViewIdler Pulley Engine Pulley Hairpin conERTensioning Chain KeeperAssembly of Snow Thrower Lockwasher Cable WireChute Crank ROD Crank Support Tube Tilt Control HANDLE--Q ChutecrankFlange Plastic CAP ANTI-ROTATIONHEX Bolt Bracket Chute KeeperAttaching Weight Tray to Tractor X 1 Slotted Truss Head Bolt ChecklisiHole with HEX Bolt Removed Square KEY Side BraceStarting HOW to USE Your Snow ThrowerKnow Your Snow Thrower Operating Speed Using the Snow ThrowerRaisingand Lowering Deep or Drifted SnowDisengagement Adjustment Skid Shoe AdjustmentLift Release Cable Adjustment Replacing Auger Drive BeltParts to Remove AT END of Season Removing the Spiral Auger HousingStorage Recommendations CauseSlope Guide Repair Parts Formodel 486.248400 Snowthrower Part QTY Description Repair Parts for Model 486.248400 40 Snow Thrower QTY Description Part MY-HOME