Husqvarna ST724 owner manual Troubleshooting Points, Trouble Cause Correction

Page 28

TROUBLESHOOTING POINTS

TROUBLE

CAUSE

CORRECTION

 

 

 

Difficult starting

Defective spark plug.

Replace defective plug.

 

Water or dirt in fuel system.

Use carburetor bowl drain to flush and refill with fresh fuel.

 

 

 

Engine runs erratic

Blocked fuel line or empty gas

Clean fuel line; check fuel supply; add fresh

 

tank or stale gasoline.

gasoline.

 

 

 

Engine stalls

Unit running on CHOKE.

Set choke lever to RUN position.

 

 

 

Engine runs erratic;

Water or dirt in fuel system.

Use carburetor bowl drain to flush and refill with fresh fuel.

Loss of power

 

 

 

Carburetor out of adjustment.

Adjust carburetor.

 

 

 

Excessive vibration

Loose parts; damaged impeller.

Stop engine immediately and disconnect spark plug wire.

 

 

Tighten all bolts and make all necessary repairs. If vibration

 

 

continues, have the unit serviced by a competent repairman.

 

 

 

Unit fails to propel

Drive belt loose or damaged.

Replace drive belt.

itself

 

 

 

Incorrect adjustment of traction

Adjust traction drive cable.

 

drive cable.

 

 

Worn or damaged friction wheel.

Replace friction wheel.

 

 

 

Unit fails to discharge

Auger drive belt loose or

Adjust auger drive belt; replace if damaged.

snow

damaged.

 

 

Auger control cable not adjusted

Adjust auger control cable.

 

correctly.

 

 

Shear bolt broken.

Replace shear bolt.

 

Discharge chute clogged.

Stop engine immediately and disconnect spark plug wire.

 

 

Clean discharge chute and inside of auger housing.

 

Foreign object lodged in auger.

Stop engine immediately and disconnect spark plug wire.

 

 

Remove object from auger.

 

 

 

29

Image 28
Contents ST724 Safety Rules Before USECalifornia Proposition 65 Warning Table of Contents Owners InformationInternational Symbols III.1 IIIIII.5 III.4III.6 III.7 III -A III -BIII.9 III III.11 III.12III.13 III.1410III.15 III.17III.18 III.19III.20 III.21III.22 III.23III.24 III.25III.26 III.27 III.28 III.29III.30 III.31III.32 III.34Assembly Contents of Shipping Tools Required for Carton AssemblyTo Install the Crank Assembly To SET the Skid HeightTo Install the Shifter ROD To CHECK/ADJUST Clutch Control CablesTo Install Chute Assembly to Chute Flange To Install Remote Chute Deflector Lever KnobOperation To Stop Engine Fill GASWarm Start Snow Throwing Tips Frozen StarterIf the starter is frozen and will not turn engine Maintenance General RecommendationsService and Adjustments To Adjust Skid HeightTo Adjust Scraper BAR To Adjust the Clutch Control CablesTo Adjust the Belt Guides Traction Drive BeltTo Replace Belts Auger Drive BeltTo Adjust the Friction Wheel To Replace Friction WheelTo Replace Auger Shear Bolt Drain Gasoline Outdoors Away from Fire or FlameTo Adjust Carburetor To Adjust or Replace the Spark PlugTo Adjust To ReplaceStorage Snow ThrowerTroubleshooting Points Trouble Cause CorrectionEngine Repair Parts Snow Thrower Model STFrame Repair Parts NUT, 1/2 Push onDrive Component Repair Parts Gear BOX Repair Parts Auger Housing Repair Parts 505497 504 506 532 500Discharge Chute Repair Parts Wheel Assembly Repair Parts 673 675 653 671 650 678 676 652 655 656 654 677Handles Repair Parts Control Panel Repair Parts 774 770 772 773 784 789 788 790View from Rear Tank DecalsChute Control ROD Repair Parts 856 854 855 850 860 863 861 875 872 864 873 866 874 867