Husqvarna 16530 EXL, 96193006900, 96193006901 manual Before Starting the Engine

Page 12

OPERATION

NOTE: It is not recommended to operate the snow thrower over gravel or rocky surfaces. Objects such as gravel, rocks or other debris, can easily be picked up and thrown by the impeller, which can cause serious personal injury, property damage or damage to the snow thrower.

•If snow thrower must be operated over gravel surface, use extra caution and be sure skid plates are adjusted to lowest (highest scraper clearance) position.

1.Shut off engine and wait for all moving parts to stop.

2.Adjust skid plates by loosening the 1/2" hex nuts, then moving skid plate to desired position. Be sure both plates are adjusted evenly. Tighten securely.

SCRAPER BAR (See Fig. 19)

The scraper bar is not adjustable, but is reversible. After considerable use it may become worn. When it has worn almost to the edge of the housing, it can be reversed, providing additional service before requiring replacement. Replace a damaged or worn scraper bar.

HIGH POSITION

HEX

(LOW GROUND

CLEARANCE)

NUTS

 

AUGER

 

HOUSING

LOW POSITION

SCRAPER

(HIGH GROUND

BAR

CLEARANCE)

SKID PLATE

 

FIG. 19

TO USE DRIFT CUTTERS (See Fig. 20)

Use the drift cutters to cut through deep snowdrifts that are higher than the front of the snow thrower.

•Loosen adjustment nuts enough to allow drift cutter to be raised to highest position and tighten nuts securely. Repeat for opposite side of snow thrower.

•When not using drift cutters, loosen adjustment nuts, lower to storage position and tighten nuts securely.

AUGER

HOUSING

STORAGE

DRIFT

POSITION

CUTTER

ADJUST-

MENT NUTS

FIG. 20

TO TRANSPORT (See Fig. 21)

When pushing or towing your snowthrower, be sure to disengage transmission by placing freewheel control into FREEWHEEL position. Freewheel control is located at the rear of snowthrower.

•Pull freewheel control out to FREEWHEEL position.

•To reengage transmission, push control back in.

FREEWHEEL POSITION

TRANSMISSION ENGAGED

FIG. 21

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL (See Fig. 22)

The engine on your snow thrower has been shipped from the factory already filled with oil.

1.Check engine oil with snow thrower on level ground.

2.Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•To change engine oil, see “TO CHANGE ENGINE OIL” in the Maintenance section of this manual.

CHOKE

ENGINE OIL

GASOLINE

CONTROL

FILL CAP / DIPSTICK

FILLER CAP

 

 

FUEL SHUT-

 

 

OFF VALVE

 

 

STARTER

 

 

BUTTON

PRIMER

RECOIL

 

SAFETY

STARTER

HANDLE

IGNITION

THROTTLE

KEY

NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION. ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.

FIG. 22

ADD GASOLINE (See Fig. 22)

•Fill fuel tank to bottom of tank filler neck. Do not over- fill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

WARNING: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents 16530 EXL Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Chute Deflector Remote Control Parts Packed Separately in CartonEXT RA Shear Bolts and Nuts Rotator Head MountingAssembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerRemove Snow Thrower from Carton Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Operation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting engineHOW to USE Your Snow Thrower StoppingUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Adjust Skid Plates See Fig To Move Forward and Backward See FigBefore Starting the Engine Snow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationCleaning Snow ThrowerEngine Service and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting Limitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart 532 43 58-96 05.19.10 TH

96193006901, 96193006900, 16530 EXL specifications

The Husqvarna 16530 EXL is a robust and versatile lawn mower designed to meet the needs of homeowners who demand efficiency and performance in their outdoor maintenance tasks. With model numbers 96193006901 and 96193006900, this mower stands out for its combination of advanced features, cutting-edge technology, and user-friendly operation.

One of the key characteristics of the Husqvarna 16530 EXL is its powerful engine. This mower is equipped with a reliable engine that provides ample power for tackling even the toughest grass and uneven terrains. The engine's design ensures excellent fuel efficiency, allowing users to mow large areas without frequent refueling.

The cutting deck of the Husqvarna 16530 EXL is engineered for precision and durability. It features a wide cutting width, which enables users to cover more ground in less time. The deck height can be easily adjusted, offering versatility for different grass lengths and types, ensuring that lawn care is tailored to the specific needs of each yard.

Another notable feature of the Husqvarna 16530 EXL is its innovative blade design. The mower is equipped with high-performance blades that deliver a clean and even cut, promoting healthy grass growth. Additionally, the mower's mulching capability allows for efficient nutrient recycling, as finely cut grass clippings are returned to the lawn, enriching the soil.

The design of the Husqvarna 16530 EXL prioritizes user comfort and ease of use. With ergonomic handles and intuitive controls, the mower provides a smooth and enjoyable mowing experience. The lightweight construction adds to the mower's maneuverability, making it easy to navigate around obstacles.

In terms of technology, the Husqvarna 16530 EXL incorporates features such as anti-vibration systems, which reduce fatigue during prolonged use. The mower is also designed for easy maintenance, with accessible components that facilitate quick and hassle-free servicing.

Durability is another hallmark of the Husqvarna brand, and the 16530 EXL is no exception. Built with high-quality materials, this mower is designed to withstand the rigors of regular use, ensuring longevity and reliability.

In summary, the Husqvarna 16530 EXL (96193006901, 96193006900) offers an impressive blend of power, efficiency, and user-friendly features. With its advanced technology, ergonomic design, and durable construction, this mower is an excellent choice for homeowners looking to maintain a beautiful and healthy lawn with ease.
Top Page Image Contents