Husqvarna 96193006700, 14527E manual Meets A.N.S.I. Safety Requirements

Page 9

OPERATION

GASOLINE

FILLER CAP

MUFFLER

CHOKE CON-

ELECTRIC AUGER

START CONTROL

BUTTON LEVER

RECOIL (AUXILIARY)

STARTER

HANDLE

CHUTE DEFLECTOR

DISCHARGE CHUTE CONTROL LEVER

DRIVE SPEED

DEFLECTOR

TRACTION

CONTROL LEVER

REMOTE

DRIVE

 

CONTROL

CONTROL

 

LEVER

LEVER

TROL

PRIMER

SAFETY IGNITION KEY

FUEL SHUT-OFF

VALVE THROTTLE / ENGINE CONTROL

DISCHARGE

CHUTE

CLEAN-OUT TOOL

LH TURN TRIGGER

LIGHT

HANDLE

KNOB

NOTE: ITEMS ABOVE

ARE SHOWN IN

THEIR TYPICAL

LOCATION ON THE ENGINE. ACTUAL LOCATION MAY VARY WITH THE ENGINE ON YOUR UNIT.

MUFFLER

TOOLBOX

DRIFT

CUTTER

AUGERS

SKID PLATE

 

Fig. 10

MEETS A.N.S.I. SAFETY REQUIREMENTS

Our snow throwers conform to the standards of the American National Standards Institute.

Toolbox - used to store spare shear bolts, locknuts and wrench.

Safety ignition key - must be inserted for the engine to start and run. Remove when snow thrower is not in use.

Electric start button - used for starting the engine.

Recoil (auxiliary) starter handle - used for starting engine.

Primer - pumps additional fuel from the carburetor to the cylinder for use when starting a cold engine.

Choke Control - used for starting a cold engine.

Throttle/engine control - used to select either FAST or SLOW engine speed and to STOP the engine.

LH and RH turn triggers - used to steer the snow thrower.

Drive speed control lever - used to select forward or reverse motion and speed of snow thrower.

Traction drive control lever - used to engage power-pro- pelled forward or reverse motion of snow thrower.

Auger control lever - used to engage auger motion (throw snow).

Discharge chute control lever - used to change the di- rection the snow is thrown.

Deflector remote control lever - used to change the di- stance the snow is thrown.

Skid plate - used to adjust height of scraper bar from the ground.

Drift cutter - used to cut through deep snowdrifts.

9

Image 9
Contents 14527E Thoroughly inspect the area where the equipment is Never attempt to make any adjustments whileEngine motor is running except when specifically Crushed rock surfaceTable of Contents Parts Packed Separately in Carton Chute Deflector Remote ControlEXT RA Shear Bolts and Nuts Rotator Head MountingHOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Know Your Snow Thrower OperationPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting engineAuger control lever used to engage auger motion throw snow Stopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Release the auger control lever and shut off the engineBefore Starting the Engine To Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenGeneral Recommendations MaintenanceBefore Each USE LubricationEngine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigRemove the klik pin and remove wheel from axle CarburetorOther StorageFuel System Engine OILTroubleshooting Limitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart 532 43 59-02 05.20.10 TH See Separate Engine Manufacturers or Manufacturers warranty