Husqvarna 924HV, 96193005200 manual To Replace Belts See Fig

Page 17

SERVICE AND ADJUSTMENTS

TO REPLACE BELTS (See Fig. 21)

The auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear, they should be replaced. It is recommended that the belt(s) be replaced by a Sears service center/department.

NOTE: It is recommended that both the auger and traction drive belt be replaced at the same time.

The V-belts on your snow thrower are of special construction and should be replaced by original equipment manufacturer (OEM) belts available from your nearest Sears service center/department. Using other than OEM belts can cause personal injury or damage to the snow thrower.

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistant stand in the operating position and hold the snow thrower handles. Serious personal injury and/ or damage to the unit could occur if the snow thrower should fall during the belt changing process.

FRAME

AUGER

ASSEMBLY

HOUSING

HANDLES

1.REMOVE GASOLINE FROM FUEL TANK - Drain gasoline from fuel tank into a suitable container, out- doors, away from fire or flame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen locknut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY - Remove bolt, flat washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two (2) bolts holding the auger housing and frame together.

WARNING: As the last bolt is removed, have your assistant carefully lower the handles down to the ground.

6.

REMOVE HAIRPIN FROM CLUTCH ROD and re-

 

move clutch rod from swing plate. Tip swing plate

 

forward.

7.

REMOVE AUGER BELT from around pulley.

8.RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around pulleys.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.

9.With tension relieved on idler, install new traction drive belt around pulleys and inside belt keepers.

10.Install clutch rod in swing plate; secure with hairpin.

11.Place auger belt around and inside the groove of auger pulley only.

12.While your assistant slowly raises handles to rejoin the auger housing and frame assembly, pull up on the auger belt and squeeze sides together above pulley so belt is fully seated in groove of pulley.

13.Move idler arm so it does not hit impeller pulley as you bring snow thrower completely together and check carefully for proper routing of belts. If auger belt has become dislodged from the pulley (by catching the idler arm bracket while bringing snow thrower together), separate the snow thrower and repeat step 12. Belt must be fully seated in pulley groove when bringing the snow thrower together.

14.Install the two (2) hex bolts and tighten securely.

15.INSTALL ENGINE PULLEY - Place belt in pulley groove and slide pulley on crankshaft. Install flat washer, bolt and tighten securely (41-47 N-m torque). Make sure belt is inside belt keeper.

16.INSTALL BELT COVER and two (2) screws. Tighten securely.

17.INSTALL DISCHARGE CHUTE – See “INSTALL DIS- CHARGE CHUTE / CHUTE ROTATER HEAD” in the Assembly / Pre-Operation section of this manual.

 

BELT KEEPER

 

 

TRACTION DRIVE BELT

 

ENGINE

FLAT WASHER

 

PULLEY

 

 

 

 

BOLT

IDLER ARM

AUGER

SQUARE

BELT

HOLE

 

 

CLUTCHING

 

 

IDLER ARM

 

 

BRACKET

 

FRAME

AUGER PULLEY

AUGER

HOUSING

 

 

 

BOLTS

17

FIG. 21

Page 16 Page 18
Image 17
Page 16 Page 18
Contents 924HV Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsKnow Your Snow Thrower OperationPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow ThrowerTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See FigTo Adjust Skid Plates See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Move Forward and Backward See FigScraper BAR See Fig Before Starting the EngineCheck Engine OIL Level See Fig ADD Gasoline See FigIf Recoil Starter has Frozen Snow Throwing TipsBefore Stopping General Recommendations MaintenanceBefore Each USE LubricationEngine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigCarburetor Engine SpeedOther StorageFuel System Engine OILTroubleshooting Service Notes Service Notes Service Notes Warranty Statement

924HV, 96193005200 specifications

The Husqvarna 924HV, model number 96193005200, is a top-of-the-line snowblower designed for residential use, tackling heavy snowfall with ease. This robust machine is engineered to handle the challenges of winter weather while providing exceptional performance and user comfort.

One of the standout features of the Husqvarna 924HV is its powerful 24-inch clearing width combined with an impressive intake height of 23 inches. This allows it to clear large paths of snow quickly and efficiently, making it ideal for driveways, sidewalks, and yards. The snowblower is equipped with a durable and reliable 291cc engine that provides substantial power for effective snow removal, even on the heaviest snowfalls.

The Husqvarna 924HV also boasts innovative technologies that enhance its overall performance. The machine features self-propelled drive with six forward speeds and one reverse speed, providing users with optimal control and maneuverability. This is particularly beneficial when navigating through deep snow or tight areas. The adjustable skid shoes further allow for customization based on surfaces, maximizing efficiency and minimizing surface damage.

Another noteworthy characteristic is its exceptional throwing capability. The machine can throw snow up to 35 feet, allowing for efficient clearing of areas without needing to reposition constantly. The adjustable chute direction and deflector enable users to precisely control where the snow is being expelled, making it easier to clear paths without unnecessary hassle.

The operator's comfort is also a top priority in the design of the Husqvarna 924HV. The spacious, ergonomically designed handles are adjustable, ensuring that users can find the most comfortable position while operating the snowblower. The heated grips provide warmth during cold winter days, allowing for extended usage without discomfort.

In conclusion, the Husqvarna 924HV, model number 96193005200, is engineered for those who need a reliable and powerful snow removal solution. With its robust engine, efficient clearing capabilities, and user-friendly features, it stands as an exceptional choice for homeowners looking to tackle winter snowstorms with confidence and ease. Whether facing light flurries or heavy snowfalls, the Husqvarna 924HV is a dependable partner in maintaining clear pathways and driveways all winter long.
Top Page Image Contents