Husqvarna 924HV, 96193005200 manual Storage, Other, Fuel System, Engine OIL, Cylinder

Page 19

STORAGE

Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS” in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

•Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in mini- mizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

•Remove safety ignition key; store it in a safe place.

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your snow thrower indoors and cover it to protect it from dust and dirt.

•Cover your snow thrower with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe, which allows condensation to form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/ exhaust area is still warm.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents 924HV Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerMeets A.N.S.I. Safety Requirements To USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To USE Fuel SHUT-OFF Valve See FigTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Adjust Skid Plates See Fig To Throw Snow See FigADD Gasoline See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsIf Recoil Starter has Frozen Lubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Service Notes Service Notes Service Notes Warranty Statement

924HV, 96193005200 specifications

The Husqvarna 924HV, model number 96193005200, is a top-of-the-line snowblower designed for residential use, tackling heavy snowfall with ease. This robust machine is engineered to handle the challenges of winter weather while providing exceptional performance and user comfort.

One of the standout features of the Husqvarna 924HV is its powerful 24-inch clearing width combined with an impressive intake height of 23 inches. This allows it to clear large paths of snow quickly and efficiently, making it ideal for driveways, sidewalks, and yards. The snowblower is equipped with a durable and reliable 291cc engine that provides substantial power for effective snow removal, even on the heaviest snowfalls.

The Husqvarna 924HV also boasts innovative technologies that enhance its overall performance. The machine features self-propelled drive with six forward speeds and one reverse speed, providing users with optimal control and maneuverability. This is particularly beneficial when navigating through deep snow or tight areas. The adjustable skid shoes further allow for customization based on surfaces, maximizing efficiency and minimizing surface damage.

Another noteworthy characteristic is its exceptional throwing capability. The machine can throw snow up to 35 feet, allowing for efficient clearing of areas without needing to reposition constantly. The adjustable chute direction and deflector enable users to precisely control where the snow is being expelled, making it easier to clear paths without unnecessary hassle.

The operator's comfort is also a top priority in the design of the Husqvarna 924HV. The spacious, ergonomically designed handles are adjustable, ensuring that users can find the most comfortable position while operating the snowblower. The heated grips provide warmth during cold winter days, allowing for extended usage without discomfort.

In conclusion, the Husqvarna 924HV, model number 96193005200, is engineered for those who need a reliable and powerful snow removal solution. With its robust engine, efficient clearing capabilities, and user-friendly features, it stands as an exceptional choice for homeowners looking to tackle winter snowstorms with confidence and ease. Whether facing light flurries or heavy snowfalls, the Husqvarna 924HV is a dependable partner in maintaining clear pathways and driveways all winter long.
Top Page Image Contents