Husqvarna 924HV/96193007000 warranty Parts Packed Separately in Carton, Assembly / PRE-OPERATION

Page 4

PARTS PACKED SEPARATELY IN CARTON

(1) POWER CORD

(1) MULTI-

(3) RETAINER

(198563)

WRENCH

SPRINGS

 

 

(180684)

(169675)

 

(6) SHEAR BOLTS 1/4-20 x 1-3/4

(6) LOCKNUTS

 

 

1/4-20

 

(192090)

 

 

 

(73800400)

 

 

 

(2) FLAT WASHERS

 

 

 

 

SAFTEY

 

 

 

IGNITION KEY (S)

 

 

 

(422663)

 

 

(2) CARRIAGE BOLTS

(1) LOCKNUT

(1) CARRIAGE BOLT

3/8-16 x 2.25

5/16-18

 

5/16-18 x 5/8

 

(751153)

 

(72250505)

 

(1) WASHER 3/8

(1) LOCKNUT 3/8

(1) LOCKNUT

(1) SHOULDER

 

(2) HANDLE KNOBS

1/4-20

BOLT 1/4-20

(1) SPRING

(19131316)

(73800600)

(191730)

(179829)

(184505)

 

ASSEMBLY / PRE-OPERATION

Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower. Reading the entire manual will familiar- ize you with the unit, which will assist you in assembly, operation and maintenance of the product.

Your new snow thrower has been assembled at the factory with the exception of those parts left unassembled for ship- ping purposes. All parts such as nuts, washers, bolts, etc., necessary to complete the assembly have been placed in the parts bag. To ensure safe and proper operation of your snow thrower, all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to ensure proper tightness.

REMOVE SNOW THROWER FROM CARTON

1.Remove all accessible loose parts and parts boxes from carton.

2.Cut down all four corners of carton and lay panels flat.

3.Remove the two (2) screws securing the auger housing to the pallet.

4.Remove all packing materials except plastic tie holding speed control rod to lower handle.

5.Remove the two (2) plastic ties securing the upper handle to the pallet.

6.Remove snow thrower from carton and check carton thoroughly for additional loose parts.

HOW TO SET UP YOUR SNOW THROWER

TOOL BOX (See Fig. 10)

A toolbox is provided on your snow thrower. The toolbox is located on top of the belt cover. Store the extra shear bolts, nuts and multi-wrench provided in parts bag in the toolbox.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents 532 44 Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressureOperation Know Your Snow ThrowerPrimer TractionMeets A.N.S.I. Safety Requirements HOW to USE Your Snow Thrower StoppingTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See FigUsing the CLEAN-OUT Tool See Fig To Adjust Skid Plates See FigTo Throw Snow See Fig To Move Forward and Backward See FigBefore Starting the Engine Scraper BAR See FigCheck Engine OIL Level See Fig ADD Gasoline See FigBefore Stopping Snow Throwing TipsIf Recoil Starter has Frozen Maintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting Limitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart Qjlqh 7UDQVPLVVLRQ HDUV Service Notes Service Notes Service Notes 06/15/2011 SR
Top Page Image Contents