Husqvarna 10527STE owner manual Meets A.N.S.I. Safety Requirements

Page 9

OPERATION

SPARK

PLUG

SAFETY

IGNITION

KEY

CHOKE

CON-

TROL

THROTTLE

 

/ ENGINE

 

CONTROL

 

RECOIL

POWER

(AUXILIARY)

CORD

STARTER

PLUG ELECTRIC

HANDLE

 

START

 

BUTTON

PRIMER

 

NOTE: ITEMS ABOVE

ARE SHOWN IN

THEIR TYPICAL

LOCATION ON THE

ENGINE. ACTUAL

LOCATION MAY VARY

WITH THE ENGINE

ON YOUR UNIT.

AUGERS

ENGINE OIL CAP

AUGER

DISCHARGE CHUTE CONTROL LEVER

WITH DIPSTICK

CONTROL

 

DEFLECTOR REMOTE

 

LEVER

DRIVE SPEED

 

 

CONTROL LEVER

 

 

CONTROL LEVER

 

 

 

GASOLINE

FILLER

CAP

CHUTE

DEFLECTOR

OIL

DRAIN

PLUG

DISCHARGE

CHUTE

FUEL SHUT-OFF VALVE

CLEAN-OUT TOOL

FIG. 10

TRACTION

DRIVE

CONTROL

LEVER

LH TURN

TRIGGER

LIGHT

HANDLE

KNOB

MUFFLER

TOOLBOX

SKID PLATE

MEETS A.N.S.I. SAFETY REQUIREMENTS

Our snow throwers conform to the standards of the American National Standards Institute.

Toolbox - used to store spare shear bolts, locknuts and wrench.

Safety ignition key - must be inserted for the engine to start and run. Remove when snow thrower is not in use.

Electric start button - used for starting the engine.

Recoil (auxiliary) starter handle - used for starting engine.

Primer - pumps additional fuel from the carburetor to the cylinder for use when starting a cold engine.

Throttle/engine control - used to select either FAST or SLOW engine speed and to STOP the engine.

Drive speed control lever - used to select forward or reverse motion and speed of snow thrower.

Choke control - used for starting a cold engine.

Traction drive control lever - used to engage power-pro- pelled forward or reverse motion of snow thrower.

LH and RH turn triggers - used to steer the snow thrower.

Deflector remote control lever - used to change the distance the snow is thrown.

Auger control lever - used to engage auger motion (throw snow).

Discharge chute control lever - used to change the di- rection the snow is thrown.

Skid plate - used to adjust height of scraper bar from the

9 ground.

Image 9
Contents 10527STE Preparation TrainingOperation Static Electricity HazardAPI SG-SL Maintenance and StorageParts Packed Separately in Carton Service and Adjustments14-15 16-18HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Know Your Snow Thrower OperationRecoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Move Forward and Backward See FigBefore Starting the Engine Scraper BARTo Start Engine Snow Throwing Tips Before StoppingIf Recoil Starter has Frozen General Recommendations MaintenanceBefore Each USE LubricationEngine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Other StorageTroubleshooting Repair Parts KEY Part Description Control Panel / Discharge Chute Repair Parts Repair Parts Handles Handles Drive Repair Parts Chassis / Engine / Pulleys KEY Part Description Wheels / Decals 532 18 78-32 Wheel Assembly, 16, Power Steering, LH Sion Tmita ILD NA SON ITP Eexc 4ON ITC ES Rantywar Tementsta