Bolens 3BA, 3AA warranty Electric Starterif equipped, Before Stopping, To Stop The Snow Thrower

Page 10

5

Operation

WARNING

Severe damage to electric starter is possible if you continue to crank for more than

5 seconds without

a cool-down.

The temperature of muffler and the surrounding areas may exceed 150o F. Avoid these areas

Electric Starter(if equipped)

Some models of the snow thrower may be equipped with an optional 120 volt A.C. electric starter. This electric starter, with a three-wire power cord and plug, is designed to operate on 120 volt AC household current. Follow the steps below to use the electric starter.

Cold Start:

1.Determine whether your house wiring is a three-wire grounded system. Ask a licensed electrician if you are not certain.

WARNING: The electric starter must be properly grounded at all times to avoid the possibility of electric shock to the operator. If your house wiring system is not a three-wire grounded system, do not use this electric starter under any conditions.

2.If your house wiring system is grounded and a three- hole receptacle is not available at the point the snow thrower starter will normally be used, one should be installed by a licensed electrician.

NOTE: When connecting the power cord, always connect cord to starter on engine first, then plug the other end into a three-hole grounded 120 Volt receptacle. When disconnecting the power cord, always unplug the end from the three-hole, grounded receptacle first.

3.Attach spark plug wire to spark plug.

4.Make sure that the auger control and the drive control are disengaged.

5.Remove the keys from the plastic bag. Push key into the ignition slot. Do not turn the key. Keep second key in a safe place.

6.Move the choke knob to FULL choke position.

7.Move throttle control to the FAST position.

8.Turn fuel valve on, if so equipped.

9.Connect power cord to the switch box on engine.

10.Plug the other end of the power cord into a three- hole, grounded 120 volt AC receptacle.

11.Push primer button three times.

12.Push down on the starter button until the engine starts. Do not crank for more than 5 seconds at a time.

WARNING: Severe damage to electric starter is possible if you continue to crank for more than 5 seconds without

acool-down.

13.When the engine starts, release the starter button and slowly rotate the choke to OFF position. If the engine falters, rotate the choke to FULL and then gradually to OFF.

NOTE: When engaging the electric starter, a slight hesitation of a few seconds may occur before the engine starts to turn. This is normal and is not harmful to the engine.

14.Disconnect the power cord from the receptacle first and then from the switch box on the engine.

15.Allow the engine to warm up for a few minutes because the engine will not develop full power until it reaches operating temperature.

NOTE: If the starter motor runs but the engine does not turn over, the starter gear may have frozen. Place the snow thrower in a warmer part of the garage or storage shed till the gear is free of the accumulated ice.

Warm Start:

1.If restarting a warm engine, rotate choke to OFF instead of FULL and press the starter button. Do not push the primer button.

Before Stopping

1.Run engine for a few minutes to help dry off any moisture on engine.

2.To avoid possible freeze-up of the starter, follow these steps:

Recoil Starter

a.With the engine running, pull the starter rope with a rapid, continuous full arm stroke three or four times.

Electric Starter (if equipped)

a.Connect power cord to switch box, then to 120 Volt AC receptacle.

b.While the engine is running, push the starter button and spin the starter for several seconds.

c.Disconnect power cord from the receptacle first, then from the snow thrower.

NOTE: The unusual sound from pulling the starter rope or from spinning the starter will not harm the engine.

3.While standing in the operator’s position (behind the snow thrower), engage the auger control for a few seconds to clear any remaining snow and ice from the chute assembly.

To Stop The Snow Thrower

1.To stop the wheels, release the drive control.

2.To stop throwing snow, release the auger control.

3.To stop engine, push throttle control lever to OFF or pull out the key(either method works). Do not turn key.

WARNING: The temperature of muffler and the surrounding areas may exceed 150º F. Avoid these areas

Auger Control Test

IMPORTANT: Perform the following test before operating the snow thrower for the first time and at the start of each winter season.

Check the adjustment of the auger control as follows:

1.When the auger control is released and in the disengaged “up” position, the cable should have very little slack, but should NOT be tight.

10

Image 10
Contents OPERATOR’S Manual Table of Contents Safety Labels Your ResponsibilityPractices Safe OperationTrainingPreparation Safe Operation Practices Maintenance & StorageOperation Clean-Out Tool Before AssemblySetting Up The Handle Final AdjustmentsSkid Shoe Adjusting Auger CableRouting The Drive Cable Know Your Snow Thrower Before Starting Engine OperationTo Start Engine To Stop The Snow Thrower Electric Starterif equippedBefore Stopping Auger Control TestOperating Tips Cleaning The Chute AssemblyClearing The Snow Stop engine byMaintenance Service Auger Belt Before servicing Repairing, or inspectReplacing Belts Drive BeltPreparing Engine Do not drain Carburetor if using Fuel stabilizerOff-Season Storage Preparing Snow ThrowerPlease do not Trouble ShootingLog onto Or call a customer Dual Stage Snow Thrower Part ListPart Description 549 144 2022 3435 710-0449 MANUFACTURER’S Limited Warranty for