Assembly Instructions and Installation

ASSEMBLY INSTRUCTIONS AND INSTALLATION

INSTALLATION INSTRUCTIONS:

The Meyer MDV Series Spreaders can mount and store as a single unit. The Meyer MDV Series Spreader will mount on most 15,000-20,000 GVW trucks as well as larger trucks.

!WARNING

DO NOT OVERLOAD THE VEHICLE. It is quite possible to overload the vehicle by improperly mounting or over loading the spreader. This could result in dangerous stability and braking problems. Always consult and follow the truck manufacturer’s instructions.

!WARNING

BEFORE BEGINNING ANY INSTALLATION ON THIS UNIT, disconnect the spreader battery negative cable if already installed.

1.Place the spreader in the rear of truck with the engine / hydraulic motor to the rear of the truck. Center the spreader (side to side) in the truck. The spreader should extend past the rear of the outer most part of the truck (i.e: truck bed, bumper) approximately 18 inches.

!Caution: Insure that the spreader cannot tip when the spinner assembly is attached.

SPINNER ASSEMBLY

a.Raise engine shroud and prop it open with the support rod. (if engine driven model)

b.Slide the spinner frame assembly into the rear of the longitudinals with the spinner back plate toward the rear.

c.Bolt the spinner to the longitudinals using the four (4) 3/8" x 1” bolts, 3/8” flange nuts and flatwashers from hardware bag located on the spinner. Using one (1) 3/8" x 1" bolts, flatwashers and flange nut from hardware bag, bolt the top portion of the spinner back plate to the engine plate.

d.Install roller chain between the gear box sprocket and the spinner sprocket. Make sure sprockets are in line with each other. The roller chain is tightened, first by loosening all four 3/8" bolts on the back plate. Then, pull the entire bearing/shaft assembly in such a way to achieve the proper amount of chain tension. Make sure the spinner shaft is straight up and down before retightening.

2.Reposition the spreader in the truck, just short of making contact with the rearmost part of the truck bed, bumper, pintle hook etc. Bolt the unit to the truck using a minimum of six 1/2" - grade 5 bolts and corresponding washers and locknuts. The Spreader is designed to sit flat on the bed of the truck, supported by the longitudinal/sides. DO NOT SUPPORT THE SPREADER BY THE BODYJACKS ALONE !! UNIT IS NOT DESIGNED FOR CHASSIS MOUNT APPLICATION !

M-1044, M-940, M-944 specifications

Power Acoustik is known for its innovation in the mobile audio industry, and their line of amplifiers, including the M-940, M-944, and M-1044, exemplifies this commitment to performance and quality. These amplifiers are engineered to deliver superior sound quality, remarkable power handling, and advanced features that cater to audiophiles and casual listeners alike.

The Power Acoustik M-940 is a robust 4-channel amplifier designed to boost your audio setup. With a peak power output of 940 watts, this amplifier is perfect for driving high-performance speakers, ensuring clear sound reproduction and dynamic bass response. The M-940 employs MOSFET power supply technology, which allows for increased efficiency and minimized distortion, resulting in a clean audio signal across all frequency ranges. Additionally, its variable low-pass and high-pass filters provide flexibility in tuning frequencies, making it easier to achieve the desired sound profile for any listening environment.

Stepping up in power and features, the M-944 offers even greater performance with its 4-channel configuration capable of delivering 944 watts of peak power. It shares the same MOSFET technology as the M-940 but includes a built-in crossover network that enables more precise control over sound frequencies. The M-944 is equipped with thermal and short circuit protection to ensure longevity and reliability, making it suitable for extended listening sessions. Its stylish design and compact form factor also allow for easy installation in a variety of vehicle types.

Finally, the Power Acoustik M-1044 is the powerhouse of the trio, catering specifically to those looking for serious bass performance. As a monoblock amplifier, the M-1044 is capable of producing an impressive 1044 watts of peak power specifically tailored for subwoofers. The M-1044 features adjustable bass boost and phase control, enabling users to fine-tune their bass response for maximum impact. Its heavy-duty construction ensures durability, even under demanding conditions.

Each of these amplifiers employs advanced technology to ensure optimal performance. With features such as RCA inputs, variable gain control, and remote bass level adjustments, Power Acoustik amplifiers provide versatility and ease of use. The combination of power handling capabilities, sound clarity, and user-friendly features makes the M-940, M-944, and M-1044 excellent choices for anyone looking to enhance their mobile audio experience. Whether you prefer crystal-clear highs or booming bass, Power Acoustik has an amplifier to meet your audio needs.