Spreader Operation

D.TO CONTROL Conveyor Speed.

1.Hold HI to increase speed. NOTE: Do not hold switch in HI position after the desired RPM is achieved or you will choke and/or stall the engine.

2.Hold LO to decrease speed.

E.TO DISENGAGE Spreader Conveyor.

1.Tap START switch momentarily so that red indicator light goes out. Do not fully depress the START switch, only half way is needed. Only the conveyor stops, the engine continues to run.

F.TO TURN ENGINE OFF (with or without conveyor running).

1.Depress LO on throttle control to reduce setting to idle (this prevents engine flooding and hard starting).

2.Push OFF position on the ON/OFF switch.

NOTE: OFF can be pushed at anytime during spreader operation to cut power to the unit. However, you should normally use steps under F above.

(Once the off switch is depressed - the starting procedure must be followed for engine re-start.)

G.Do not attempt to start the engine with the conveyor engaged. (CONV switch light will be lit to indicating its’ being on.)

!WARNING

1 . As with all power equipment, safety is the number one concern.

2.Do not operate this equipment until you fully understand how it functions.

3.Before starting engine, be sure that no one is near the rear of the unit and that no one is inside the unit!

4.Do not start the engine or engage the conveyor (which is interconnected to the spinner); until everyone is clear from moving parts and flying material from the spinner.

A. Start the engine and engage the clutch. The amount of material spread, depends on engine speed and gate opening. Decreasing RPM and/or gate height will decrease amount spread; the inverse holds true also. Notice that the electric clutch can be engaged or disengaged at any time and at any engine RPM. However, since engagement time and torque is almost instantaneous, to prevent premature spinner chain failure and chain tension loss, it is recommended that the electric clutch be engaged at the lowest possible RPM without stalling the engine.

If the truck is to be driven for an extended period of time while the spreader is not operating, it is best to turn off the gas at the carburator inlet to prevent the carburator from overfilling with fuel.

Before loading the spreader the first time, start and stop the conveyor several times to break in the clutch.

M-1044, M-940, M-944 specifications

Power Acoustik is known for its innovation in the mobile audio industry, and their line of amplifiers, including the M-940, M-944, and M-1044, exemplifies this commitment to performance and quality. These amplifiers are engineered to deliver superior sound quality, remarkable power handling, and advanced features that cater to audiophiles and casual listeners alike.

The Power Acoustik M-940 is a robust 4-channel amplifier designed to boost your audio setup. With a peak power output of 940 watts, this amplifier is perfect for driving high-performance speakers, ensuring clear sound reproduction and dynamic bass response. The M-940 employs MOSFET power supply technology, which allows for increased efficiency and minimized distortion, resulting in a clean audio signal across all frequency ranges. Additionally, its variable low-pass and high-pass filters provide flexibility in tuning frequencies, making it easier to achieve the desired sound profile for any listening environment.

Stepping up in power and features, the M-944 offers even greater performance with its 4-channel configuration capable of delivering 944 watts of peak power. It shares the same MOSFET technology as the M-940 but includes a built-in crossover network that enables more precise control over sound frequencies. The M-944 is equipped with thermal and short circuit protection to ensure longevity and reliability, making it suitable for extended listening sessions. Its stylish design and compact form factor also allow for easy installation in a variety of vehicle types.

Finally, the Power Acoustik M-1044 is the powerhouse of the trio, catering specifically to those looking for serious bass performance. As a monoblock amplifier, the M-1044 is capable of producing an impressive 1044 watts of peak power specifically tailored for subwoofers. The M-1044 features adjustable bass boost and phase control, enabling users to fine-tune their bass response for maximum impact. Its heavy-duty construction ensures durability, even under demanding conditions.

Each of these amplifiers employs advanced technology to ensure optimal performance. With features such as RCA inputs, variable gain control, and remote bass level adjustments, Power Acoustik amplifiers provide versatility and ease of use. The combination of power handling capabilities, sound clarity, and user-friendly features makes the M-940, M-944, and M-1044 excellent choices for anyone looking to enhance their mobile audio experience. Whether you prefer crystal-clear highs or booming bass, Power Acoustik has an amplifier to meet your audio needs.