Meade LXD75 instruction manual Method 3 Axis Alignment Using Autostar, Tips

Page 55

AC

Motor at back of mount

B

D

Fig. 48: Method #2 Setup. (A) Optical Tube; (B) Dec. Motor; (C) Cradle Ring Lock Knobs; (D) Eyepiece.

7.Rotate the telescope 180° in the R.A. axis ONLY, to return the optical tube to position A.

8.Repeat steps 5 through 8, if necessary, alternating between position A and posi- tion B, and bringing the reference object halfway of the remaining distance to center. Stop the procedure once the distance between the object in position A and position B is less than one third the width of the eyepiece.

9.As a final check, select another object and place it into the center of the eyepiece. Rotate the mount about the R.A. axis. Watch the motion of that object. It is acceptable if it moves slightly, but should remain in the eyepiece the entire time.

Tips

■When moving to position A or B, it is usually sufficient to merely level the Dec. axis by eye. Whether in position A or B, the counterweight shaft should appear to be horizontal when looked at from several feet away.

■If you are finding it difficult to lower the altitude of the tripod head without the counterweight banging into the forward tripod leg, increase the length of the two rear tripod legs to introduce a tilt into the whole mount.

■Before starting the alignment procedure, it is helpful to have the tripod azimuth adjustment knobs even, to allow an equal range of travel in either direction.

■Make sure the focuser lock is tightened once focus is achieved. Otherwise, grav- ity may cause the focuser to move during rotation of the telescope and introduce error into the procedure.

Method 3: Axis Alignment Using Autostar

Perform this procedure during the daytime. You will need to have an unobstructed view of an easily sighted landmark, such as a light post. Use a low-power eyepiece, such as the supplied 26mm. This procedure assumes that you have some familiarity with Autostar's menu structure (you will need to locate the "Setup: Telescope" menu). If necessary, refer to AUTOSTAR'S MENUS, page 25.

Note: For best result, perform this procedure after you have trained the drive. See page 20.

1.Adjust the latitude T-handle screws (26, Fig. 1d) so that the latitude is set to 45° or higher. See Step #6, page 12, for information about setting the latitude controls.

2.Refer to Fig. 48 while performing this step. The Dec. motor (B) must be positioned so that it is at the back of the mount. The optical tube (A) must be approximately horizontal (i.e., parallel with the horizon) and the counterweight shaft must be pointing straight down.

If using a Schmidt-Newtonian model, loosen the cradle ring locks knobs (C) and move the optical tube until the eyepiece (D) points downward as shown in the Fig. 48. Re-tighten the cradle ring locks.

If using a refractor model, use the diagonal assembly to rotate the eyepiece to a convenient viewing angle during testing. However, be careful that the diag- onal is placed flush against the focuser and tightened in place using the thumb- screws. It is important that the diagonal does not slip during the procedure.

3.Make sure that both the R.A. and Dec. locks (17 and 33, Fig. 1d) are tightened to a firm feel.

4.Turn on Autostar and go to "Setup: Telescope." Press ENTER.

5.Press one of the Scroll keys until "LXD 55 Adjust" displays and then press ENTER. A message displays that tells you to center a landmark. If the landmark is not visible in your eyepiece, lift and move the entire telescope and tripod assembly—try not to move the tube too far from the horizontal position (no more than 5° up or down), as described in Step #2. You may also use the fine azimuth controls (27, Fig. 1d) for side to side movement and the Autostar Up/Down Arrows for small adjustments to the declination axis.

6.Caution: Before pressing ENTER, step back from the telescope assembly, as the telescope will begin to rotate about two axes. When the landmark is centered (Step #5), press ENTER.

55

Page 54 Page 56
Image 55
Page 54 Page 56
Contents LXD 75 -Series Telescopes Page Contents BC1 g f e Telescope FeaturesD E F LXD75-SeriesYour Personal Window to the Universe $ Computer Control Panel see e LXD75 Tips Features Autostar FeaturesTour the Cosmos with Just the Push of a Button Tip Getting Started How to Assemble Your TelescopeTelescope Assembly AccessoriesViewfinder assembly Newtonian reflector models Balancing the Telescope C D E FChoosing an Eyepiece Aligning the ViewfinderObserving by Moving the Telescope Manually Too Much Power?Slew Speeds Autostar Models Only Activate the Arrow Keys Autostar Models Only16b Setting the Polar Home PositionObserve the Moon Tracking ObjectsUsing Autostars GO to Capabilities Autostar Models Only Observe a Star using the Automatic Tracking FeatureInitializing Autostar Autostar Models Only Moving Through Autostar’s Menus Autostar Models OnlyTraining the Drive Autostar Models Only Go To Saturn Autostar Models Only Easy Alignment Autostar Models OnlyPlanet Saturn is over 800 million miles from the Earth Using the Guided Tour Autostar Models OnlyTo Calculate Sunset time Autostar Navigation ExerciseNavigating Autostar Entering Data into AutostarSelect Item Object Autostars MenusObject Menu MenusLXD75-Series Event MenuGlossary Menu Utilities MenuEnter Setup MenuObserving Considerations Setup Menu Daylight SAVING, Surf the Web To Add a Site to the user-defined site list Adding Observing SitesTo Edit a Site To GO to a user-entered object Using Autostar to Find Objects Not in the LibrariesLandmarks Observing SatellitesTo Add a landmark to the database To Select a landmark from the database To Check on the Available MemoryTo perform a Landmark Survey Few tips on photography with the LXD75-Seriestelescopes PhotographyPhotography with Meade’s Autostar Suite 10 f/4 Optional AccessoriesSeries 4000 Photo-Visual Optional Autostar handbox for EC model users General Maintenance MaintenanceD e f g Page Defocused star images. Misaligned 1, 2, Aligned Page Page 5 Model SN-6AT, SN-6EC Specifications Specifications4 Model SN-8AT, SN-8EC Specifications 9.3 Model AR-5AT, AR-5EC Specifications 10 f/4 Model SN-10AT Specifications8 Model AR-6AT Specifications 5 Model N-6EC Specifications 10 Model SC-8AT SpecificationsInspecting the Optics Autostar SpecificationsAutostar Dimensions Meade Customer ServiceAppendix a Celestial Coordinates Setting CirclesTwo-Star Polar Alignment Locating the Celestial PolePolar Alignment One-Star Polar AlignmentTo perform the Three-Star Alignment Method #1 Three-Star Alignment Using AutostarPolar Alignment Viewfinder Enhancement MethodsProcedure #1 To correct for attitude misalignment Method 2 Axis Alignment ProceduresPosition a Procedure #2 To correct for elevation misalignmentTips Method 3 Axis Alignment Using AutostarPEC Erase Menu Option Method #4 Smart Drive Training Periodic Error CorrectionPEC Update Menu Option PEC Train Menu OptionCity Country Latitude Appendix C Latitude ChartLatitude Chart for Major Cities of the World City State/Prov./Country LatitudeAppendix D EC Handbox Modes of Operation To move the telescope using the Electronic ControllerSlew Speeds Tracking Rates Optional Autostar Computer Controller for LXD75 EC Users Changing the Polar ModeMounting the SC bracket and optical tube to the mount How to Attach the Optical Tube to the MountMoon Appendix F Basic AstronomyAutostar Glossary Objects in SpaceDeep-Sky Objects PlanetsFurther Study Page Meade Limited Warranty

LXD75 specifications

The Meade LXD75 series represents a remarkable range of telescopes designed for both amateur astronomers and advanced users seeking high-quality performance at an affordable price. Known for its robust construction and innovative technology, the LXD75 aims to provide a user-friendly experience while catering to the demands of stargazers looking for sophistication in their equipment.

One of the main features of the LXD75 is its advanced German equatorial mount, which provides exceptional stability and tracking accuracy. This mount is equipped with dual-axis servo motors facilitating smooth movements, making it easy to locate and follow celestial objects. The LXD75 also includes a built-in autostar system featuring a database of over 30,000 celestial objects, allowing users to effortlessly navigate the night sky with a push of a button.

The LXD75 series includes several models, each with different optical configurations to suit the preferences of various users. The telescopes come with either an achromatic refractor or Schmidt-Cassegrain optical design, providing clear and bright images. The Schmidt-Cassegrain models offer a compact design with a fast focal ratio, making them excellent for both astrophotography and visual observation.

In terms of build, the Meade LXD75 features high-quality optics with multi-coated lenses, reducing glare and enhancing light transmission. This results in sharper and brighter images, making it easier to observe delicate details on planets, the moon, and deep-sky objects. The telescope tubes are crafted from durable materials, ensuring longevity and resilience against the elements.

Another characteristic worth noting is the ease of setup and operation. The LXD75 mount comes equipped with adjustable legs and can be easily assembled, requiring minimal tools. The intuitive control system also features a user-friendly interface, allowing both novices and experienced astronomers to operate the telescope with confidence.

For astrophotography enthusiasts, the LXD75 provides excellent support, with a wide range of accessories available to enhance imaging capabilities. The mount can accommodate various cameras, providing flexibility for capturing stunning astronomical photographs.

In summary, the Meade LXD75 series delivers a robust combination of features, technologies, and characteristics designed to meet the needs of both amateur and advanced astronomers. With its reliable mount, quality optics, and ease of use, the LXD75 ensures that stargazers can enjoy the wonders of the universe with clarity and precision.
Top Page Image Contents