Orion XT8 CLASSIC, XT10 CLASSIC instruction manual Assembly of the Dobsonian Base

Page 4

 

C

 

 

 

C

 

 

B

 

 

L

 

 

I

J

 

H

 

 

E

 

D

 

 

A

K

 

 

 

 

F

 

 

G

Figure 2. Exploded view of the SkyQuest XT Dobsonian base.

2. Assembly

Now that you have unpacked the boxes and familiarized your- self with all the parts in front of you, it’s time to begin assembly. The optics of the telescope are already installed in the tube, so most of the required assembly concerns the Dobsonian base.

Assembly of the Dobsonian Base

Refer to Figure 2 during base assembly. The base need only be assembled once, unless you disassemble it for long-term storage. The assembly process takes about 30 minutes and requires a Phillips screwdriver, an adjustable crescent wrench, and the provided hex keys.

Note: When tightening the base assembly screws, tight- en them until firm, but be careful not to strip the holes by over-tightening. If you use an electric screwdriver, do the final tightening with a standard screwdriver to avoid stripping.

1.Screw the plastic feet into the underside of the ground baseplate (A) using the self-tapping wood screws provid- ed, with a Phillips screwdriver. Insert the screws through the feet and thread them into the predrilled starter holes.

2.Loosely attach the front brace (B) to the two side panels

(C) with six of the base assembly screws in the predrilled holes. Use the 4mm hex key to tighten the screws. The side panels should be oriented so the SkyQuest label is facing outward. Do not completely tighten the screws yet.

Figure 3. Set the optical tube on the “cradle” of the base so that the altitude side bearings on the tube rest on the white plastic “pads,” and the finder is facing away from the front brace (Part B).

3.Attach the two sides (C) with the front brace attached to the top baseplate (D) with the remaining six base assembly screws in the predrilled holes. Tighten all six screws.

4.Tighten the six side panel screws installed earlier.

5.Insert the white nylon bushing (E) into the hole in the cen- ter of the top baseplate (D). Tap the nylon bushing in so it goes all the way into the top baseplate. The nylon bushing should be flush with the top surface of the top baseplate.

6.Insert the T-nut (K) into the center hole of the ground base- plate (A) so the nut’s flanged top is on the same side of the baseplate as the Teflon pads. Thread the large hex-head bolt (G) with a 3/8" washer (F) attached up through the ground baseplate and through the T-nut until it is tight. Now position the top baseplate (D) (with side panels attached) over the ground baseplate and lower it so the bolt goes through the nylon spacer in the center hole of the top baseplate. Now thread the remaining 3/8" washer (H) and lock nut (I) onto the bolts shaft. You might need to hold the bolts head in place with another crescent wrench or pliers. Tighten the lock nut with the wrench just enough to allow a slight separation of the top and bottom baseplates when the mount is lifted. The purpose of the lock nut is merely to keep the two baseplates from coming apart when moving the telescope.

Note: Overtightening the lock nut (I) will make the mount difficult to rotate in the azimuthal (horizontal) direction.

7.Attach the handle (J) to the front brace (B) with the two black socket-head screws. Insert the screws through the handle and into the predrilled holes. Place the 5/16" wash- ers and 5/16" nuts on the protruding ends of the screws. Tighten the nuts with a crescent wrench while holding the bolts stationary with the 6mm hex key.

8.Lift the optical tube and set the altitude bearings on either side of the tube in the “cradle” of the base (Figure 3). The unique flange design of the altitude bearing allows for auto- matic left-to-right centering of the optical tube in the cradle.

4

Image 4
Contents Orion SkyQuest XT6 Classic, XT8 Classic XT10 Classic SkyQuest XT Dobsonian XT6 pictured Parts List Table of ContentsUnpacking Assembly Assembly of the Dobsonian BaseInstalling the EZ Finder Installing the Optional Eyepiece RackOperation Installing the CorrecTension XT Friction Optimization System Using Your Telescope Focusing the TelescopeInserting an Eyepiece Altitude and AzimuthReplacing the Battery Aligning the EZ FinderAiming/Pointing the Telescope MagnificationTube Balance CollimationCarrying the Telescope Collimation Cap and Mirror Center Mark Aligning the Secondary MirrorAdjusting the Primary Mirror Star-Testing the TelescopeAstronomical Observing Site SelectionCooling the Telescope Seeing and TransparencyUsing 2 Eyepieces XT8 and XT10 Eyepiece SelectionTracking Celestial Objects MoonHow to Find Deep-sky Objects Starhopping SunPlanets StarsCleaning Lenses Care and MaintenanceCleaning Mirrors Specifications SkyQuest XTCollimatible One-Year Limited Warranty Hangar Way, Watsonville, CA

XT10 CLASSIC, XT8 CLASSIC specifications

The Orion XT10 Classic and XT8 Classic telescopes represent a perfect blend of innovative design and advanced optics, making them excellent choices for amateur astronomers. Both models are part of Orion's popular XT Classic series, known for their user-friendly features and high-quality performance.

The Orion XT10 Classic features a large 10-inch aperture, providing exceptional light-gathering capabilities. This allows users to observe faint celestial objects, such as distant galaxies, nebulae, and star clusters, with remarkable clarity and detail. The telescope's Dobsonian mount ensures smooth and stable movement, making it easy to track objects across the night sky.

The XT8 Classic, with its 8-inch aperture, also offers impressive light-gathering ability, delivering crisp views of various astronomical phenomena. Both models are equipped with a parabolic mirror design, which minimizes optical aberrations and enhances image quality. This design is a significant advancement over traditional spherical mirrors, allowing for sharper and more focused images.

One of the standout features of both Telescopes is their simplicity of use. The intuitive Dobsonian mounting system allows users to easily position the telescope and locate celestial objects without the complexity of motorized tracking systems. This makes them ideal for novices as well as experienced astronomers looking for a portable option.

Both models come with a sturdy, pre-assembled base, ensuring stability during observations. The XT10 Classic and XT8 Classic also include high-quality eyepieces, which enhance viewing experiences. Optional accessories, such as additional eyepieces and filters, can further expand the observational capabilities.

The Orion XT10 Classic offers a focal length of 1200mm, while the XT8 Classic has a focal length of 1200mm as well. This allows both telescopes to excel in a variety of observational scenarios, from lunar observations to deep-sky exploration. Additionally, both telescopes feature a single-focal point, which makes them compatible with numerous aftermarket eyepieces.

In summary, the Orion XT10 Classic and XT8 Classic telescopes are distinguished by their user-friendly design, exceptional optical performance, and robust construction. They are perfect for anyone interested in exploring the wonders of the universe, providing a gateway to breathtaking views of the night sky. Whether you choose the larger XT10 Classic or the more compact XT8 Classic, both models are bound to enhance your astronomical experience.