Orion XX14I instruction manual Parts List, Box #1A IntelliScope Object Locator Kit refer to Figure

Page 5

Altitude encoder	Manual
and board assembly

IntelliScope Object Locator

Azimuth encoder

cable (shorter)

Azimuth encoder

disk

Altitude encoder cable (longer)

9-Volt

Azimuth battery encoder

board

										Cable
										clips
										clips
Encoder					Controller coil cable					(x6)
Encoder
connecting										Altitude retaining
board										Altitude retaining
board				Encoder						knob spacer
				Encoder						knob spacer
				connect.
Hook-and-loop				board						Azimuth encoder
Hook-and-loop				washers						Azimuth encoder
adhesive strips				washers	Bumper	Altitude encoder nylon				spacer washer,
adhesive strips				(x4)	Bumper	Altitude encoder nylon				spacer washer,
				(x4)		spacer washers (x2)				thin
						spacer washers (x2)				thin

Figure 3. The parts contained in the IntelliScope Object Locator box.

Parts List

Box #1: Optical Tube Assembly and Accessories (refer to Figure 2)

Qty. Description

1Lower optical tube section

1Upper optical tube section

2Dust covers

1IntelliScope Object Locator kit (see Box #1A at right for list of parts)

1 35mm Deep View eyepiece, 2" barrel diameter

110mm Sirius Plössl eyepiece, 1.25" barrel diameter

19x50 finder scope

1Finder scope bracket with O-ring

1Cooling accelerator fan kit

1Collimation cap

3Hex keys (2mm, 2.5mm, 4mm)

6Counterweights, 2.3 lbs. (1.0 kg)

1XX14i Instruction Manual (not shown)

Box #1A: IntelliScope Object Locator Kit (refer to Figure 3)

Qty. Description

1IntelliScope Object Locator (hand controller)

1Altitude encoder assembly (board and disk)

1Azimuth encoder board

1Encoder connector board

1Azimuth encoder disk

1Controller cable (coil cable)

1Azimuth encoder cable (shorter)

1Altitude encoder cable (longer)

1Azimuth encoder spacer washer, thin (1/4" outer dia., 0.015" thick)

4 Encoder connector board washers (3/8" outer dia.)

2Altitude encoder nylon spacer washers (1/4" outer dia., white)

6Wire clips

19V Battery

1Hook-and-loop adhesive strips

1Altitude encoder bumper

1Altitude retaining knob spacer (3/16" thick, ½" dia., white)

1 Computerized Object Locator Instruction Manual

5

Image 5

Contents #9791 Orion SkyQuest IntelliScope Truss Tube DobsonianSkyQuest XX14i IntelliScope Truss Tube Dobsonian Unpacking Table ContentsNavigation Knob Box #1A IntelliScope Object Locator Kit refer to Figure Parts ListBox #3 Dobsonian Base refer to Qty. Description Box #2 Primary Mirror and Cell refer to FigureTop baseplate Box #4 Truss poles refer to Figure AssemblyAssembly of the Dobsonian Base Exploded view of the XX14i base Azimuth encoder board Brass azimuth Bushing Nylon spacer Assembly of the Optical Tube Page Ring Connector Truss poles Mounting the Optical Tube on Dobsonian Base Installing the Finder Scope and Eyepieces Adapter Thumb screws Coarse Focus Collimation Cap Aligning Collimating the Optical SystemPrimary Mirror Center Mark Preparing the Telescope for CollimatingAligning the Secondary Mirror Adjusting the Secondary Mirror’s Axial PositionAdjusting the Secondary Mirror’s Radial Position Adjusting the Secondary Mirror’s Tilt Adjusting the Secondary Mirror’s Rotational PositionStar-Testing the Telescope Aligning the Primary MirrorAltitude and Azimuth Motion Using Your TelescopeSetting the Altitude Tension Aligning the Finder Scope Focusing the TelescopeViewing with Eyeglasses Aiming/Pointing the Telescope Focusing the Finder ScopeMagnification 1650mmDisassembly of the Base Disassembly of the Optical TubeTube Balance Disassembling the Telescope for TransportIntelliScope Computerized Object Locator Astronomical ObservingSeeing and Transparency Selecting an Observing SiteUse of the Optional Light Shroud Eyepiece Selection Cooling the TelescopeLet Your Eyes Dark-Adapt Moon Astronomical ObjectsCleaning Mirrors Care and MaintenanceCleaning Eyepiece Lenses Page Optical Tube Assembly OTA SpecificationsAccessories MountOne-Year Limited Warranty