iOptron 8602, 8600, 8603 and 8604 instruction manual Telescope Assembly, Preparing the Tripod

Page 7

2. Telescope Assembly

Step 1. Preparing the Tripod

1. Extend tripod legs to full extension.

2. Slide tray on bottom of shaft (#7). Then screw on round black knob (#9).

Step 2. Attaching the Mount

1. Raise wedge plate on the tripod by turning two tilt locks (12);

Attach mount to wedge plate using supplied azimuth lock screw (10).

3.lower wedge plate to it’s lowest position by turning the upper tilt lock upward while lightly push the mount down. Secure the mount by tightening the lower lock.

Step 3a. Installing Batteries (not included)

Note: you may use 8 AA batteries (Step 3) or the AC adaptor (Step 5) to operate the mount.

Pull the batteries compartment cover (shown) open. Gently pull the batteries holder (shown next) out of the compartment to avoid breaking the attached wires.

Step 3b.

Insert 8 AA batteries (not included) according to the diagrams on the holder. Refer to the diagram on the holder to orient the batteries properly. Replace the holder back into the batteries compartment and replace the cover.

For reference: the battery pack fits in with wires on the bottom right (See arrow in photo). Use only fresh batteries. Using/mixing old or low batteries may cause error messages.

Optional AC Adapter and Car Charger accessories are available at www.ioptron.com

Step 4. Attaching Telescope

Attach telescope to mount using the dovetail lock knob

Dovetail(#2).

lock (#2)(Picture shows 80mm refractor. However all scopes will attach in the same manner.)

7

Image 7
Contents SmartStarCubeTM-A Series Mount and Telescopes Table of Content Never USE a Telescope to Look AT the SUN SmarStar CubeTM-A Series Overview SmartStar CubeTM-A Series FeaturesFor Model 8602 SmartStar CubeTM-A R80 Assembly Terms Preparing the Tripod Telescope AssemblyDo not plug non-iOptron accessories into the unit to For 90mm Maksutov-Cassegrain #8504………………………………… Key Description GoToNova 8401 Hand ControllerLCD Screen Level the Mount Setting Up the MountGetting Started Level and Align the MountPress ENTER. Select Set Up Local Time Set Up Local Time and Site InfoDo not Count Daylight Saving Time Set Mount TypeScroll down and select Set anti-backlash Set Anti-backlashGo to the Moon Using your telescopeInitial Star Alignment Turn Off the MountOperate SmartStar CubeTM-A mount in EQ Mode Page Manual Operation of a Telescope Use SmartStar CubeTM-A TelescopesSlew to an Object Electric Focuser Sync to TargetSet Up Controller One Star Align Three-Star Align Dis R.A axis errorAlign Set LanguageAuto Guide Set Up TrackingPEC Option User Object ListMaintenance Maintenance and ServicingStorage and Transport Cannot seem to focus No image appears in the eyepiece TroubleshootingIOptron Customer Service Page Newtonian Reflector Telescope Appendix A. Technical SpecificationsSmartStar CubeTM-A Goto Mount Refractor TelescopeMenu Appendix B. GoToNova 8401 HC Menu StructurePage GoToNova Deep Sky Object List Appendix C. GoToNova Star List5373 Messier Modern Constellations GoToNova Named Star List GoToNova Double Star List Install CP210x usb2com driver Appendix D. Set Up USB-PC ConnectionPage When finished installation, click Finish Page Page Page Page Appendix E. Firmware Upgrade Page Typical Errors Appendix F. Use a PC to Control an iOptron Mount
Related manuals
Manual 48 pages 10.2 Kb Manual 4 pages 51.1 Kb Manual 4 pages 11.84 Kb

8603 and 8604, 8602, 8600 specifications

The iOptron 8604, 8602, 8603, and 8600 series are innovative telescopes designed to enhance the stargazing and astrophotography experience for both amateur astronomers and seasoned enthusiasts. Each model in this series boasts distinct features and advanced technologies, making them suitable for a variety of applications in the field of astronomy.

The iOptron 8604 sets itself apart with its robust GoTo mount capability, allowing users to easily locate and track celestial objects with precision. This model incorporates a high-performance altitude-azimuth design, which provides smooth motion and enhanced stability. The telescope is equipped with a user-friendly hand controller that includes a database of thousands of celestial objects, making observation straightforward and enjoyable. Additionally, the 8604 offers a maximum payload capacity, allowing users to attach various accessories for a full astrophotography setup.

The iOptron 8602 also includes the GoTo mount feature, but its design focuses on portability. Weighing less than its counterparts, the 8602 is an ideal choice for those who want to explore the night sky from different locations without the hassle of heavy equipment. Despite its lightweight construction, the 8602 does not compromise on stability, ensuring that users can enjoy clear and detailed views of their astronomical targets.

The iOptron 8603 introduces advanced tracking features that facilitate long-exposure astrophotography. With built-in autoguiding ports and customizable tracking options, the 8603 is tailored for hobbyists who want to capture breathtaking images of distant galaxies and nebulae. Its sturdy mount allows for high precision and minimal vibrations during exposure, critical for obtaining sharp images.

Lastly, the iOptron 8600 series model excels in its versatility. Users will appreciate its ability to function as both a visual and astrophotography telescope. The 8600 is engineered with exceptional optics that provide clear and luminous views, while its advanced electronic features enhance the user experience. With easy setup and intuitive controls, the 8600 allows astronomers of all skill levels to navigate the night sky with confidence.

In summary, iOptron's 8600 series telescopes combine innovative technology, user-friendly features, and robust designs, making them exceptional choices for anyone looking to explore the wonders of the universe. Whether seeking to observe planets, star clusters, or engage in astrophotography, the iOptron 8604, 8602, 8603, and 8600 models cater to a wide range of astronomical interests.