Celestron C6-RGT manual Balancing the Tube in R.A, Telescope Tube Completely

Page 12

Eyepieces are commonly referred to by focal length and barrel diameter. The focal length of each eyepiece is printed on the eyepiece barrel. The longer the focal length (i.e., the larger the number) the lower the eyepiece magnification (i.e., power) and the shorter the focal length (i.e., the smaller the number) the higher the magnification. Generally, you will use low-to-moderate power when viewing. For more information on how to determine power, see the section on “Calculating Magnification.”

Your C6-R refracting telescope can use eyepieces with both a 1-1/4" barrel diameter and 2" barrel diameter. To use a 2" barrel eyepiece, the 1 1/4" eyepiece adapter must first be removed. To do this, simply loosen the two chrome thumbscrews located around the focuser barrel (see figure 2-11) and remove the 1 1/4" adapter. Once removed, a 2" eyepiece or accessory can be inserted directly into the focuser barrel and secured with the two thumb screws.

Balancing the Tube in R.A.

To eliminate undue stress on the mount, the telescope should be properly balanced around the polar axis. In addition, proper balancing is crucial for accurate tracking if using an optional motor drive. To balance the mount:

1.Release the R.A. Clamp (see figure 2-15) and position the telescope off to one side of the mount (make sure that the mounting bracket screw is tight). The counterweight bar will extend horizontally on the opposite side of the mount (see figure 2-12).

2.Release the telescope — GRADUALLY — to see which way the telescope “rolls.”

3.Loosen the set screw on the counterweight.

4.Move the counterweight to a point where it balances the telescope (i.e., it remains stationary when the R.A. clamp is released).

5.Tighten the set screw to hold the counterweight(s) in place.

These are general balance instructions and will reduce undue stress on the mount. When taking astrophotographs, this balance process should be done for the specific area at which the telescope is pointing.

Balancing the Telescope in DEC

The telescope should also be balanced on the declination axis to prevent any sudden motions when the DEC clamp (Fig 2-5) is released. To balance the telescope in DEC:

1.Release the R.A. clamp and rotate the telescope so that it is on one side of the mount (i.e., as described in the previous section on balancing the telescope in R.A.).

2.Lock the R.A. clamp to hold the telescope in place.

3.Release the DEC clamp and rotate the telescope until the tube is parallel to the ground (see figure 2-13).

4.Release the tube — GRADUALLY — to see which way it rotates around the declination axis. DO NOT LET GO

OF THE TELESCOPE TUBE COMPLETELY!

5.Loosen the screws that hold the telescope tube inside the mounting rings and slide the telescope either forwards or backwards until it remains stationary when the DEC clamp is released.

6.Tighten the tube ring screws firmly to hold the telescope in place.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Advanced Series Advanced Series GT Assembly Version Get Alt-Az Goto Alt-Az Hibernate Turn On/Off GPS Page Advanced Series C6-R C8-N ShownAdvanced Series C6-RGT Setting up the Tripod Attaching the Equatorial MountInstalling the Counterweight Bar Attaching the Center Leg BraceInstalling the Counterweight Attaching the Hand Control Holder Advanced GT Models OnlyAttaching the Telescope Tube to the Mount Installing the Finderscope Balancing the Tube in R.A Telescope Tube CompletelyAdjusting the Mount Adjusting the Mount in AltitudeAdjusting the Mount in Azimuth Powering the TelescopeAttaching the Declination Cable For GT Models Only Advanced GT Hand Control Hand Control Operation Double StarsAlignment Procedures Startup ProcedureAuto Align Auto Three-Star AlignQuick-Align Last AlignmentRe-Alignment Object Catalog Selecting an ObjectSlewing to an Object Finding PlanetsTour Mode Constellation TourDirection Buttons Rate ButtonSetup Procedures Identify Scope Setup Features Precise GoToObserving Tip Helpful Hint Utility Features Helpful Hint Advanced GT Image Orientation Focusing Aligning the FinderscopeCalculating Magnification Determining Field of View General Observing HintsCelestial Coordinate System Motion of the Stars Pointing at Polaris Finding the North Celestial Pole Declination Drift Method of Polar Alignment Observing the Moon Lunar Observing HintsObserving the Planets Observing the SunSolar Observing Hints Observing Deep Sky ObjectsSeeing Conditions TransparencyUsing the Lens Cap Aperture Stop Piggyback Short Exposure Prime Focus Photography Terrestrial Photography MeteringReducing Vibration Auto Guiding Care and Cleaning of the Optics CollimationCollimated telescope Should appear as a Page Page Page Appendix a Technical Specifications Appendix B Glossary of Terms Page Eclipsing or obscuring the brightness of the star Appendix C Longitudes Latitudes Georgia Minnesota Rhode Island Canada Appendix D RS-232 Connection Additional RS232 Commands Appendix E Maps of Time Zones Page Page Page Page Page Page Page Celestron TWO Year Warranty
Related manuals
Manual 69 pages 34.47 Kb

C6-R, C6-RGT specifications

The Celestron C6-RGT and C6-R models, part of the Advanced Series GT lineup, are popular choices for amateur astronomers seeking high-quality optics and reliable features. The C6-RGT, equipped with a 6-inch refractor, is designed for both visual and astrophotographic pursuits. Its impressive features make it a great option for anyone looking to explore the night sky in greater detail.

One of the standout characteristics of the C6-RGT is its large 6-inch aperture, which allows for exceptional light-gathering capability. This feature is crucial for viewing faint celestial objects, giving users the ability to observe details in nebulae, galaxies, and star clusters. The refractor design minimizes chromatic aberration, ensuring sharp and clear images across a wide range of viewing conditions.

The telescope comes with a fully multi-coated optics system that enhances light transmission and contrast, creating brighter and clearer images. The C6-R is also designed with a robust aluminum tube that not only ensures durability but also helps maintain stability during long observing sessions.

The Advanced Series GT mount is another essential element of the C6-RGT and C6-R models. This computerized mount features a sturdy, stable design that supports a wide range of telescopes while providing smooth tracking of celestial objects. The GoTo technology allows users to locate and track over 40,000 celestial objects with ease. This high level of automation is particularly helpful for beginners who may be unfamiliar with the night sky.

Another notable feature of the Advanced Series GT is its ability to be controlled through a smartphone or tablet, thanks to Celestron's SkyPortal app. This integration opens doors for enhanced stargazing experiences, offering customizable tours and educational information right at your fingertips.

In terms of usability, both models have a comfortable height and the mount can be easily adjusted to accommodate various observing positions. The telescope is also portable, making it convenient for outreach events or trips to dark-sky locations.

Overall, the Celestron C6-RGT and C6-R models, with their combination of powerful optics, advanced technology, and user-friendly features, represent an excellent choice for both budding astronomers and passionate enthusiasts. With Celestron’s commitment to quality and innovation, these telescopes promise to deliver unforgettable views of the wonders of the universe.
Top Page Image Contents