Makita EH6000W, EH7500W Fuels/Refueling, Fuel and oil mixture, Handling petroleum products, 501

Page 8

FUELS/REFUELING

Fuel and oil mixture

-The engine of the hedge trimmer is a high-efficiency two-stroke engine.

It is run with a mixture of fuel and two-stroke engine oil. The engine is designed for unleaded regular fuel with a min. octane value of 91 ROZ.

In case no such fuel is available, you can use fuel with a higher octane value. This will not damage the engine, but may cause poor operating behaviour.

A similar situation will arise from the use of leaded fuel.

To obtain optimum engine operation and to protect your health and the environment, only unleaded fuel should be used!

-For lubricating the engine use a two-stroke engine oil (quality grade: TSC-3), which is added to the fuel.

The engine has been designed for use with MAKITA two-stroke engine oil and a mixture ratio of 50:1 only to protect the environment. In addition, a long service life and a reliable operation with a minimum emission of exhaust gases is guaranteed. It is absolutely essential to observe a mixture ratio of 50:1 (MAKITA 2-stroke engine oil), otherwise the reliable function of the hedge trimmer cannot be guaranteed.

-The correct mixture ratio:

Gasoline: Specified two-stroke engine oil = 50 : 1 or

Gasoline: Other manufacturer’s two-stroke engine oil = 25 : 1 recommended

NOTE: For preparing the fuel-oil mixture, first mix the entire oil quantity with half of

the fuel required in an approved canister which meets or exceeds all local

code standards. Then add the remaining fuel.

Thoroughly shake the mixture before filling it into the hedge trimmer’s tank.

Do not add more engine oil than specified to ensure safe operation. It will only result in a higher production of combustion residues which will pollute the environment and clog the exhaust channel in the cylinder as well as the muffler. In addition, the fuel consumption will rise and the performance will

decrease.

Handling petroleum products

Utmost care is required when handling fuels. Fuels may contain substances similar to solvents. Refuel either in a well ventilated area or outdoors. Do not inhale fuel vapors, avoid any contact of fuel or oil with your skin.

If your skin comes in contact with these substances repeatedly and for an extended period of time, it will desiccate.

Various skin diseases may result. In addition, allergic reactions are known to occur. Eyes can be irritated by contact with oil, fuel etc.

If oil, fuel, etc., comes into your eyes, immediately wash them with clear water.

If your eyes are still irritated, see a doctor immediately!

Observe the Safety Instructions on page 4.

Gasoline

 

 

Oil

 

 

 

 

 

50:1

25:1

 

 

 

+

 

 

 

 

 

50:1

 

 

 

 

 

 

 

 

 

1,000 cm3

(1 litter)

 

 

20 cm3

40 cm3

5,000 cm3

(5 litter)

 

 

100 cm3

200 cm3

10,000 cm3

(10 litter)

 

 

200 cm3

400 cm3

 

 

 

 

 

 

 

8

Image 8
Contents Petrol Hedge Trimmer Symbols EnglishSafety Instructions General InstructionsIntended use of the machine Personal protective equipmentStarting up the hedge trimmer RefuellingDo not use any other methods for starting the engine Always ensure a safe, well-balanced footing Maintenance instructions Method of operation First aid PackagingTechnical Data Model EH5000W EH6000W EH7500WDesignation of Parts Designation of PartsFUELS/REFUELING Fuel and oil mixtureHandling petroleum products 501Precautions Before Starting Storage of fuelStarting the Machine Stopping the MachineAdjusting Rear Handle Angle Operation of the MachineSharpening blade Maintenance InstructionsAdjusting blade clearance Points in handling the air cleaner elements Checking and adjusting the idling speedCleaning the air cleaner Cleaning the fuel filter suction head in the fuel tank Daily checkup and maintenanceChecking the spark plug Supplying grease and lubricantStorage Makita Corporation