Initial Setup, Line Level Inputs | Bel Canto Design eVo200.2

Initial Setup

Line Level Inputs

Two inputs per channel are provided. The RCA jack is a standard input that accepts single- ended sources. The female XLR jack allows true balanced hookup operation using the standard pin configuration:

Pin 1	Ground
Pin 2	Input +
Pin 3	Input -

If there is a problem with noise or hum at the amplifier outputs when using a single-ended source, this may be due to the ground side of the RCA jack is not connected to the circuit ground of the amplifier. To connect this to the ground depress the RCA/XLR switch button. This should be adequate to correctly ground most systems with stereo preamplifiers.

Loudspeaker Connection and Power Output Options

Connect loudspeakers to the outputs of the eVo amplifier using the 5-way binding posts located the rear of the amplifier. The red or black center plug in the output post can be removed for use with banana type connectors. Unscrew binding post until the gold pin in the bare wire hole is visible. Remove the center pin by first pushing one end in, and then, using serrated needle nose pliers, pull the center pin out from the other side. Do not connect speaker terminals to a chassis or earth ground connection. The Anti- Phase operation of the outputs would result in one of the red (positive) outputs being connected to ground and cause the amplifier to go into protection mode and shut itself off. Also when connecting the amplifier in balanced-mode mono operation both terminals are driven actively and can not be grounded. Make certain that any output terminal is not connected to a chassis or earth ground.

Mono mode operation

Mono power delivery can be obtained with the simple push of a button. Connect one input cable to any of the 4 input jacks and depress the RCA/XLR button to select the appropriate input. Then, depress the mono/stereo mode button. The loudspeakers are then connected to the output terminals indicated for mono-mode operation on the back panel.

Power On and Operation

The rear panel has a master power switch for the eVo200.2. The eVo200.2 has been designed to remain powered up at all times. The blue front panel LED is on when the eVo200.2 is in normal operating mode. When the amplifier shuts down in protection mode a small red LED lights next to the blue LED. If this occurs, turn off the main power switch and insure that no output terminal is connected to ground or to another terminal. Restore power and the amplifier should return to normal operation. If not then there may be an internal fault and the amplifier should be returned to an authorized service center. Contact your dealer, distributor or Bel Canto Design.

eVo200.2 Owner's Manual

Page 6

eVo200.2 specifications

The Bel Canto Design eVo200.2 is a sophisticated power amplifier that exemplifies the company's commitment to delivering high-fidelity audio performance in a compact and efficient design. This amplifier represents an evolution in technology, combining modern engineering with traditional audio principles to create a listening experience that is both rich and transparent.

One of the standout features of the eVo200.2 is its Class D amplification, which offers an impressive level of power while maintaining efficiency. This design allows the amplifier to produce an exceptional 200 watts per channel into 8 ohms, ensuring that it can drive a wide range of speakers with ease. Class D technology not only reduces heat generation, but it also contributes to a more compact form factor, making the eVo200.2 an ideal choice for audiophiles with limited space.

The eVo200.2 is built upon an advanced digital switching topology that enhances audio fidelity. This amplifier utilizes proprietary technology to minimize distortion and noise, delivering an exceedingly clean signal that respects the integrity of the source material. The result is an expansive soundstage with detailed imaging, allowing listeners to appreciate the nuances of their favorite recordings.

In addition to its power and clarity, the eVo200.2 features a robust, fully balanced design that includes differential inputs. This configuration minimizes interference and optimizes signal integrity, making it compatible with a wide array of source components. The amplifier also includes high-quality speaker terminals, providing a secure and reliable connection to a variety of loudspeakers.

Another notable characteristic of the eVo200.2 is its user-friendly design. The unit includes a streamlined front panel with a minimalistic aesthetic, complemented by LED indicators that provide essential information about the amplifier's status. This simplicity does not compromise its high-end audio performance, ensuring that it fits seamlessly into any audio setup.

Moreover, the eVo200.2 is equipped with overcurrent protection and thermal management systems to safeguard its internal components, enhancing longevity and reliability. This thoughtful engineering ensures that users can enjoy years of quality performance without concerns about overheating or damage.

In summary, the Bel Canto Design eVo200.2 stands out as a premier power amplifier that combines cutting-edge technology with exceptional build quality. With its robust Class D amplification, balanced design, and intuitive user interface, it offers both performance and convenience, making it an excellent investment for any serious audio enthusiast.