Eiki LC-XNB4MS To change the code of Projector, To change the code of the Remote Control Unit

Page 36

SETTING

Power management

This function turns Projection Lamp off when this projector detects signal interruption and is not used for a certain period in order to reduce power consumption and maintain the Lamp-life. (This projector is shipped with this function ON.)

Power Management function operates to turn Projection Lamp off when the input signal is interrupted and any button is not pressed over 5 minutes. This function operates as follows;

1.When any input signal is interrupted, “No signal” and the counting down display appears (for 5 minutes).

2.After counting down for 5 minutes, Projection Lamp and READY Indicator are turned off. (Cooling Fans keep running.)

3.READY Indicator starts to flash after cooling down Projection Lamp about for 90 seconds (Power Management mode).

In this Power Management mode, Projection Lamp is automatically turned on when the input signal is connected or projector is operated with any button on Top Control or on Remote Control Unit again.

On start

When this function is “On,” projector is automatically turned on just by connecting AC Power cord to a wall outlet.

Note ; Be sure to turn projector off properly (refer to the section “TURNING OFF PROJECTOR” on P19). If projector is turned off in the wrong steps, On Start function does not operate properly.

Remote control

This projector has two different remote control codes; the factory-set normal code (Code 1) and the secondary code (Code 2). This switching function prevents remote control operation mixture (jam) when operating several projectors or video equipment together.

When operating projector in “Code 2,” both projector and Remote Control Unit must be switched to “Code 2.”

To change the code of Projector;

Set Remote control in the SETTING MENU to “Code 2.”

To change the code of the Remote Control Unit;

Press both MENU and IMAGE buttons on Remote Control Unit together for over 10 seconds.

After changing the code, make sure Remote Control Unit operates properly.

To return to the normal code (Code 1), operate both projector and Remote Control Unit in the ways above again.

NOTE : When batteries of Remote Control Unit are replaced or ALL- OFF switch is turned to “ALL-OFF,” the remote transmit code automatically returns to the normal code (Code 1).

Lamp counter reset

This function is used to reset Lamp Replace Counter. When replacing Projection Lamp, reset Lamp Replace Counter by using this function. Refer to page 38 for operation.

Time left until Lamp off.

Press SELECT button at this icon to display other items.

Press SELECT button at this icon to display previous items.

Move the pointer to the item and then press POINT LEFT/RIGHT button(s).

36

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Model LC-XNB4S LC-XNB4MS To the Owner Safety Instructions Voor de klanten in NederlandCompliances Federal Communication Commission NoticeTable of Contents Features and Design Compact Design Digital Zoom for ComputerPreparation Name of Each Part of ProjectorSETTING-UP Projector Connecting AC Power CordFor Continental Europe Adjustable Feet Preparation Positioning ProjectorPreparation Moving Projector Connecting Projector Terminals of ProjectorVideo Input Jack Terminal Input JackConnecting to Computer Connecting ProjectorTerminals Projector Connecting to Video Equipment TerminalsOperation of Remote Control Unit Before OperationRemote Control Batteries Installation TOP Controls and Indicators Lamp Replace IndicatorHOW to Operate ON-SCREEN Menu Operating ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Before Operation Menu BAR Guide WindowSound Menu Basic Operation Turning on / OFF ProjectorTurning on Projector Turning OFF ProjectorAdjusting Screen Zoom AdjustmentKeystone Adjustment Picture Freeze FunctionSound Adjustment Timer FunctionBasic Operation No Show Function Direct OperationComputer Input Selecting Input SourceSelecting Computer System RGB AnalogComputer Input Compatible Computer Specifications ResolutionFreq KHzPC Adjustment Auto PC AdjustmentPC Adjust Menu Auto PC AdjComputer Input Manual PC Adjustment Display area Display area HFull screen Picture Image Adjustments Image Level Select DirectImage Level Select Menu Image 1~4Computer Input Image Level Adjustment Image Adjust MenuPicture Screen Adjustment Screen MenuVideo Input VideoVideo Component Video Signal Format Selecting Video SystemPAL / Secam / Ntsc / NTSC4.43 / PAL-M / PAL-N AV System Menu Video or S-VIDEOCinema Video Input Image Level Adjustment ColorTint SharpnessProvides image at a normal video aspect ratio of 4 Setting Setting MenuSetting Menu To change the code of the Remote Control Unit To change the code of ProjectorLamp Replacement AppendixLamp Replace Lamp Handling Precautions Appendix Lamp Replace CounterOperating Wireless Mouse InstallationOperating Wireless Mouse Maintenance AIR Filter Care and CleaningCleaning Projection Lens Troubleshooting Remote Control Unit Wireless MouseDoes not work Function does notTechnical Specifications Appendix Configurations of Terminals Monitor OUT Terminal AnalogOptional Parts Page Page Key to better communications Canada

LC-XNB4S, LC-XNB4MS specifications

The Eiki LC-XNB4MS and LC-XNB4S are advanced projectors designed to deliver exceptional image quality and flexible performance for a variety of applications, including education, business, and home theater settings. These models stand out due to their robust specifications and innovative features, ensuring that users can enjoy stunning visuals and reliable operation.

One of the key highlights of both the LC-XNB4MS and LC-XNB4S projectors is their high brightness capability. With a brightness rating of up to 5,000 ANSI lumens, these projectors can produce clear and vibrant images even in well-lit environments. This makes them ideal for classrooms, conference rooms, and other spaces where ambient light can affect visibility. The powerful brightness is complemented by a contrast ratio of 2000:1, which enhances the depth and richness of colors, ensuring that detailed images are presented without losing clarity.

Both models utilize 3LCD technology, renowned for its ability to create bright and vivid colors while maintaining sharpness and detail. This technology reduces the risk of color decay over time and provides a more consistent color reproduction compared to DLP projectors. The Eiki LC-XNB4MS and LC-XNB4S are equipped with advanced image processing features, including edge blending and geometric correction, allowing users to create immersive multi-projection setups seamlessly.

In terms of connectivity, the projectors offer a wide range of options, including HDMI, VGA, and USB ports, ensuring compatibility with various devices such as laptops, tablets, and streaming devices. The LC-XNB4MS and LC-XNB4S also support wireless connectivity, enabling users to share content from their devices without the hassle of tangled cables. Moreover, the presenters can use the integrated network capabilities for remote monitoring and management, enhancing the ease of operation for IT administrators.

The design of the Eiki LC-XNB4MS and LC-XNB4S models prioritizes user convenience and accessibility. They feature a lightweight and compact form factor, making them easy to transport and install. The models come with a long-lasting lamp life, reducing the need for frequent replacements and ensuring lower total cost of ownership.

In summary, the Eiki LC-XNB4MS and LC-XNB4S projectors represent an excellent choice for those seeking high-performance projection solutions. With their high brightness, advanced 3LCD technology, comprehensive connectivity options, and user-friendly design, these models are set to meet the diverse needs of users across various settings.
Top Page Image Contents