Eiki LC-XG210 service manual Circuit Protections, Fuse

Page 8

Circuit Protections

This projector provides the following circuit protections to operate in safety. If the abnormality occurs inside the pro- jector, it will automatically turn off by operating one of the following protection circuits.

● Fuse

Fuse

Line Filter Board

The fuse is located inside of the projector. When either the LAMP

 

 

indicator or the READY indicator is not illuminated, fuse may be

 

 

opened. Check the fuse as following steps.

 

 

It should be used the specified fuse as follows;

 

 

FUSE PART NO. : 645 058 8181

TYPE 8A 250V FUSE

SKYGATE CO. LTD. TYPE SG-5013 008

How to replace the fuse

1.Remove the cabinet top following to “Mechanical Disassemblies”.

2.Remove the fuse from fuse holder.

To install the fuse, take reversed step in the above.

Thermal switch

There is the thermal switch (SW905) inside of the projector to

Thermal switch

prevent the internal temperature rising abnormally. When the

 

internal temperature reaches near 90˚C, turn off the AC main

 

power supply automatically.

 

The thermal switch is not reset to normal automatically even if the

 

internal temperature becomes normal. Reset the thermal switch

 

following procedure.

 

Check the resistance between terminals of thermal switch by

 

using the tester. If it has high impedance, thermal switch may be

 

in operative.

 

How to reset the thermal switch

1.Remove cabinet top following to the “Mechanical Disassemblies”.

2. Press the reset button on the thermal switch.

CAUTION:

 

 

Before press the reset button, make sure that the AC cord must

 

 

be disconnected from the AC outlet.

 

Lamp cover

Interlock switch

 

 

 

 

 

● Interlock switch

The interlock switch (SW902) cuts off the AC mains power supply when the lamp cover is removed. After opening the lamp cover for replacing the lamp ass’y, place the lamp cover correctly otherwise the projector can not turn on.

-6-

Image 8
Contents Effective from Reference NO. SM5110512-01Lamp replace counter data How to check Lamp Replace CounterCorrection Original Version Reference NO. SM5110512-00Contents Safety Instructions Safety PrecautionsSpecifications Adjustments after Parts Replacement Optical Adjustments Electrical AdjustmentsCircuit Protections FuseRecommendation Cabinet Front-Top Mechanical DisassembliesCabinet Top removal AV, COM Board & Rear Panel removal Cabinet Front removalAudio Board removal D DSpeaker base removal Optical Unit removalFan & Motor removal Lamp Ballast Board removalLine Filter Board & Interlock SW removal Fans FN901, FN902 removalOptical Parts Disassemblies Projection Lens removalPolarized Glass-In removal Lever-A1Prism ass’y removal and disassembly 2Polarized glass and optical filter mounting directionRelay Lens Relay Lens disassemblyIntegrator-In disassembly Condenser Lens disassembly Optical Unit Top removalLocations and Directions Comes to the mirror sideLCD Panel/Prism Ass’y removal LCD Panel/Prism Ass’y ReplacementImportant Notice on LCD Panel/Prism Assy Replacement Lamp Replacement How to reset Lamp Replace CounterProcedure Reset the Lamp Replace Counter, see below explanationBefore Adjustment Optical AdjustmentsContrast adjustment Condenser Lens adjustment White b Moving of Slot B Moving of Slot DRelay Lens-Out adjustment Mirror adjustment White Moving of Slot B White b Moving of Slot DElectrical Adjustments IC808 is not defectiveCircuit Adjustments Fan Voltage adjustmentVideo Center adjustment Adjustment ConditionNRS adjustment Pedestal adjustment PCVideo Gain adjustment PC Black Level adjustment PCLuminance adjustment adjustment PC D Ref. Voltage adjustment VideoPedestal adjustment Video D Input adjustment Video12 A/D Input adjustment Component Pedestal adjustment ComponentVideo Gain adjustment Component White Balance adjustmentLuminance adjustment Video Common Center adjustmentTest Points and Locations Service Adjustment Data Table Group 4 L3E07050 Group 6 TC90A69F IP Conversion Dnrynoiseth Dnrysense Dnrymotionth Group 21 MB40C348 Group 22 ICSdata Group 519 RGB PAL Gakaku View DiagramsBlock Inputs & video signal processing stage IC4261A S&H LCD AV Board Main BoardMotor driving circuit Main Board Audio BoardControl Power supply & protection circuit FAN1Abnormality occurs on the power circuit TroubleshootingNo Power No Picture No picture from Video sourceNo picture from DVI source No picture from all of sourcesLens Motor Problems No SoundControl Port Functions System Control & I/O Port Table IC801Control Port Functions Parallel I/O Expander IC1801, M66500FP Name Function Name PolarityIIC Bus DA Converter IC3291, M62398FP Port Functions IIC Bus I/O Expander IC5581, M62320FP Port FunctionsIIC Bus DA Converter IC281, M62393FP Port Functions IIC Bus DA Converter IC4881, M62393FP Port Functions IIC Bus DA Converter IC1531, M62399FP Port FunctionsIIC Bus DA Converter IC1501, M62399FP Port Functions Waveform Gvspw Tpgvs DHS Tpdhs DVS Tpdvs Cleaning Cleaning with air sprayIC Block Diagrams IC Block Diagrams BA7078AF SynC. Detector, IC7201 BA7655 Audio Pre-amp, IC001 IC Block Diagrams IC Block Diagrams M62392 D/A, IC3291 M62393 D/A, IC281, IC4881 M62399 D/A, IC1501, IC1531 ML60851 USB Driver, IC9801 IC Block Diagrams IC Block Diagrams TDA1517ATW Audio Output, IC031 Electrical Parts List Read Description in the parts listOUT of Circuit Board 610 308 1724 ASSY,PWB,MAIN MH7A Assemblied BoardsOUT of Circuit Boards Electrical Parts List Electrical Parts List Electrical Parts List Integrated Circuit Capacitor C145 403 283 POS-SOLID C343 403 164 MT-GLAZE Resistor Network MT-GLAZE 1K JA R239 401 2003 R3205 401 105 7909 R414 401 3901 R4829 401 105 7909 MT-GLAZE 3K FA Transformer 610 301 1950 ASSY,PWB,TEMP.SENSOR MC3A 610 302 6435 ASSY,PWB,AUDIO MC3ATemp Sensor Board Board 610 303 4799 ASSY,PWB,A/V MC3BIC UPD78F9801GB-8ES-MC3A FILTER,EMI 25MHZ Front Board 610 304 9502 ASSY,PWB,R/C Front MC3BCOM Board 610 306 0279 ASSY,PWB,COM. MC3ABIC AD8185ARU C3081 403 164 0204 Control Board 610 303 4812 ASSY,PWB,CONTROL MC3BAccessories Key No. Part No DescriptionMechanical Parts List M15 M14Optical Parts L10 100 ZoomFocus L14 L22 L23 102 Mechanical Parts List 103 Key to better communications Canada
Related manuals
Manual 1 pages 30.71 Kb

LC-XG210 specifications

The Eiki LC-XG210 is a high-performance LCD projector designed for professional presentations and educational use. This projector stands out due to its impressive brightness, exceptional image quality, and versatile connectivity options, making it an ideal choice for a variety of settings, including classrooms, conference rooms, and auditoriums.

One of the primary features of the Eiki LC-XG210 is its remarkable brightness, with a lumen output of 3,200 ANSI lumens. This high brightness level ensures that presentations remain vibrant and clear, even in well-lit environments. Coupled with a native resolution of XGA (1024 x 768 pixels), the projector delivers sharp text and detailed images, making it suitable for displaying both graphics and video footage.

The LC-XG210 utilizes advanced 3LCD technology, which ensures accurate color reproduction and enhanced color brightness. This technology provides a wide color gamut, allowing users to enjoy rich and lifelike colors without any noticeable color distortion. The projector also features a high contrast ratio, contributing to deeper blacks and more vivid images, further enhancing the overall viewing experience.

Connectivity is a crucial aspect of the Eiki LC-XG210, and it excels in this area with a range of input options. It includes multiple VGA inputs, composite and S-Video inputs, as well as a USB port for easy connection to computers and other devices. This flexibility allows users to seamlessly switch between different sources without the need for additional adapters.

Additionally, the projector is equipped with a powerful built-in speaker that delivers clear audio, eliminating the need for external sound systems in smaller venues. Its lightweight and portable design make it easy to transport, enabling users to set it up quickly in various locations.

The Eiki LC-XG210 also boasts a user-friendly interface and advanced features such as automatic keystone correction, which simplifies the setup process by automatically adjusting the image to fit the screen perfectly. This projector is designed for reliability and longevity, evident in its long lamp life of up to 5,000 hours in eco mode, reducing maintenance costs and enhancing overall value.

In summary, the Eiki LC-XG210 is a versatile and powerful projector that combines high brightness levels, advanced LCD technology, and extensive connectivity options. These features make it an excellent choice for any professional or educational environment, ensuring outstanding image quality and reliability for diverse presentation needs.