Eiki LC-UXT3 Appendix Lamp Management, Yellow Lamp Dim Lamp Red Lamp Mark on Lamp

Page 45

APPENDIX

LAMP MANAGEMENT

This Projector is equipped with 4 Projection Lamps to ensure brighter image and those lamps are controlled by Lamp Management Function. Lamp Management Function detects status of all lamps and shows status on screen or on LAMP REPLACE indicator. This function also automatically controls Lamp Mode when any of lamps is out for end of life or malfunctions.

LAMP STATUS

INPUT 1

1 3

2 4

30

LAMP REPLACE

INDICATOR

Lamp Replace Indicator

This LAMP REPLACE indicator lights yellow when any of Projection Lamps is nearing its end, and flashes when any of them becomes out. Check number of lamp on Lamp Status Display and replace lamp.

Lamp Status Display

Lamp Status Display appears on screen when power switch is on or changed input position (input 1, input 2, Input 3 or input 4). This shows status of each lamp as; ON, OFF, NEAR END, or OUT. Refer to following for each status.

13

24

LAMP STATUS DISPLAY

Yellow Lamp

Dim Lamp

Red Lamp

X Mark on Lamp

Projection Lamp lights normally.

Projection Lamp is turned off.

Projection Lamp is nearing its end. When image becomes darker or color becomes unnatural, replace lamp. (LAMP REPLACE indicator lights yellow.)

(LAMP REPLACE indicator flashes yellow.)

Projection lamp is defective or fails to be turned on. Restart a projector on, and make sure lamp is on. If this mark still appears, replace lamp corresponding with number marked X.

Lamp Mode Changeover

Lamp Management Function automatically changes combination of lighting lamp (Lamp Mode) by detecting status of lamp. When any of 4 lamps becomes out, Lamp Mode is changed over from 4 lamps to 2 lamps. And when any of 2 lamps are out, a projector operates with 1 lamp. Lamp Mode can be switched to 4 lamps or 2 lamps manually. Refer to SETTING section on page 40, 41.

13

24

4 LAMP MODE

13

24

2 LAMP MODE (Example)

1

3

2

4

1 LAMP MODE (Example)

NOTE

It takes approximately 3 minutes until the projector stabilizes its lamp condition. Accordingly, the lamp status display which is shown just after the count-down display can be different from the actual status. To confirm the proper status, (press INPUT button or select Lamp Mode in the setting menu) over 3 minutes after turning on the projector.

45

Page 44 Page 46
Image 45
Page 44 Page 46
Contents Multimedia Projector Model LC-UXT3Risk of Electric Shock Do not Open To the OwnerVoor de klanten in Nederland Safety InstructionsFederal Communication Commission Notice CompliancesTable of Contents Compatibility Features and DesignName of Each Part of Projector PreparationSETTING-UP Projector Connecting AC Power CordFor U.S.A. and Canada For Continental Europe Preparation Lens Installation Lens Shift AdjustmentPositioning Projector Moving Projector Preparation Picture Level and Tilt AdjustmentConnecting Projector Replacement of TerminalTerminals of Projector BNC Input Jacks Connecting Projector INPUT/OUTPUT Terminals and Jacks InputAudio Input Jacks AV Input VIDEO/Y, C JacksSerial Port Terminal Reset ButtonSerial Port OUT Terminal JackTerminals Projector Connecting to ComputerTerminals Connecting to Video EquipmentSide Controls and Indicators Before OperationSide Controls Ready Indicator IndicatorsLamp Indicator Lamp Replace IndicatorLaser Pointer Function Operation of Remote ControlWired Remote Jack Volume ButtonZoom Button Focus ButtonHOW to Operate ON-SCREEN Menu Operating ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Before Operation Menu BAR Turning on / OFF Projector Basic OperationTurning on Projector Turning OFF ProjectorZoom Adjustment Adjusting ScreenFocus Adjustment Keystone AdjustmentTimer Function Basic Operation Picture Freeze FunctionNo Show Function Direct Operation Sound AdjustmentMenu Operation Sound MenuSelecting Input Source Computer InputSelecting Computer System InputSelect Computer System Manually Computer Input Automatic MULTI-SCAN SystemAuto PC System MenuResolution Computer Input Compatible Computer SpecificationsAuto PC Adjustment PC AdjustmentPC Adjust Menu Computer InputComputer Input Manual PC Adjustment Display area Display area HFull screen Image Level Select Direct Picture Image AdjustmentImage Level Select Menu Image 1~4Image Adjust Menu Computer Input Image Level AdjustmentScreen Menu Picture Screen AdjustmentVideo Input When Select Input 2 5 BNC TerminalSelecting Video System Component Video Signal FormatVideo Input PAL / Secam / Ntsc / NTSC4.43 / PAL-M / PAL-NCinema Color Video Input Image Level AdjustmentTint Progressive scanProvides image at a normal video aspect ratio of 4 Setting Setting MenuSetting Menu To change code of Projector To change code of Remote Control UnitProjector mode Wireless Mouse modeLamp counter reset USBMaintenance Operating Wireless MouseInstallation Operating Wireless MouseCleaning Projection Lens Appendix AIR Filter Care and CleaningYellow Lamp Dim Lamp Red Lamp Mark on Lamp Appendix Lamp ManagementFront Indicators Rear Indicators Appendix Lamp ReplacementLamp Handling Precautions Troubleshooting Wireless Mouse Remote Control UnitDoes not work Function does notTechnical Specifications DVI-I Terminal DIGITAL/ANALOG Appendix Configurations of TerminalsSerial Port IN/OUT Terminal Appendix Appendix Appendix Key to better communications Canada

LC-UXT3 specifications

The Eiki LC-UXT3 is an advanced multimedia projector that excels in delivering high-quality presentations and engaging visual experiences across various environments. Designed for versatility, it is ideal for educational institutions, corporate offices, and large venues.

One of the standout features of the LC-UXT3 is its impressive resolution. With a WUXGA resolution of 1920 x 1200 pixels, it provides sharp and detailed images that enhance the viewing experience. This high resolution is particularly beneficial for displaying intricate graphics, texts, and videos, making it suitable for both professional and educational use.

The projector boasts a powerful brightness level of 6000 lumens, ensuring vivid images even in well-lit rooms. This high lumen output allows for optimal performance during daytime presentations or in environments where light control is limited. Additionally, the LC-UXT3 features a high contrast ratio, which enhances color accuracy and depth, giving presentations a professional touch.

In terms of connectivity, the Eiki LC-UXT3 excels with multiple input options, including HDMI, VGA, and composite video ports. This versatility allows users to connect a variety of devices such as laptops, tablets, and other multimedia sources seamlessly. Furthermore, the projector supports wireless connectivity, enabling easy interactions with devices without the need for messy cables.

The LC-UXT3 incorporates advanced technology to enhance its performance. With its 3LCD technology, the projector delivers bright and vibrant colors while minimizing the risk of the "rainbow effect" often associated with single-chip projectors. This technology ensures accurate color reproduction, making it perfect for dynamic presentations that require color precision.

Another noteworthy characteristic of the Eiki LC-UXT3 is its extensive range of lens options, which allows for flexible installation setups. The motorized lens shift, zoom, and focus features facilitate easy adjustments, making it an ideal choice for various rooms and setups.

In conclusion, the Eiki LC-UXT3 is a feature-rich multimedia projector that combines high brightness, resolution, and connectivity options, making it an excellent choice for professional and educational settings. Its advanced technologies and flexible installation capabilities make it a reliable tool for any presentation need, ensuring a powerful and engaging visual experience every time.
Top Page Image Contents