Eiki LC-UXT3 instruction manual Appendix Lamp Replacement, Front Indicators Rear Indicators

Page 46

APPENDIX

LAMP REPLACEMENT

When the life of the Projection Lamp of this projector draws to an end, the LAMP REPLACE indicator lights yellow. If this indicator lights yellow, replace the projection lamp with a new one promptly.

FRONT INDICATORS

 

REAR INDICATORS

 

 

 

LAMP

READY

WARNING

LAMP TEMP. REPLACE

LAMP

READY

WARNING

TEMP.

LAMP

REPLACE

LAMP REPLACE

INDICATOR

CAUTION

Allow a projector to cool, for at least 45 minutes before

 

For continued safety, replace with a lamp assembly of

you open Lamp Cover. The inside of a projector can

 

the same type.

become very hot.

 

Do not drop a lamp assembly or touch a glass bulb! The

 

 

glass can shatter and may cause injury.

 

 

 

Follow these steps to replace lamp assembly.

1

Check number of lamp to be replaced on Lamp Status Display.

 

2

Turn off a projector and disconnect AC Power Cord. Allow a

projector to cool down for at least 45 minutes.

3

Remove two screws on Lamp Cover and press button to open

 

4

Lamp Cover. (See right figure.)

Loosen two screws and pull out Lamp Assembly to be replaced

 

5

by grasping handle.

Replace Lamp Assembly with a new one and tighten two screws.

 

6

Make sure Lamp is set properly

Replace Lamp Cover and tighten two screws.

 

7

Connect AC Power Cord to a projector and turn a projector on.

 

8

Reset Lamp Replacement Counter. (Refer to section "Lamp

Counter Reset" on page 42.)

NOTE : Do not reset LAMP REPLACEMENT COUNTER when lamp is not replaced.

BUTTON

LAMP

COVER SCREWS

SCREWS

LAMP 3

LAMP 1

LAMP 4

LAMP 2

Make sure which number of lamp needs to be replaced on Lamp Status Display.

Figure shows case of replacing LAMP 2.

CAUTION : DO NOT OPERATE A PROJECTOR WHILE ANY OF LAMPS IS REMOVED. IT MAY RESULT IN MALFUNCTIONS, FIRE HAZARD, OR OTHER ACCIDENTS.

NOTES ON LAMP REPLACEMENT

To maintain quality of picture (better balance of color and brightness in entire screen), we recommend replacing all 4 lamps at a time.

46

Page 45 Page 47
Image 46
Page 45 Page 47
Contents Model LC-UXT3 Multimedia ProjectorTo the Owner Risk of Electric Shock Do not OpenSafety Instructions Voor de klanten in NederlandCompliances Federal Communication Commission NoticeTable of Contents Features and Design CompatibilityPreparation Name of Each Part of ProjectorConnecting AC Power Cord SETTING-UP ProjectorFor U.S.A. and Canada For Continental Europe Lens Shift Adjustment Preparation Lens InstallationPositioning Projector Preparation Picture Level and Tilt Adjustment Moving ProjectorReplacement of Terminal Connecting ProjectorTerminals of Projector Audio Input Jacks Connecting Projector INPUT/OUTPUT Terminals and Jacks InputBNC Input Jacks AV Input VIDEO/Y, C JacksSerial Port OUT Terminal Reset ButtonSerial Port Terminal JackConnecting to Computer Terminals ProjectorConnecting to Video Equipment TerminalsBefore Operation Side Controls and IndicatorsSide Controls Lamp Indicator IndicatorsReady Indicator Lamp Replace IndicatorOperation of Remote Control Laser Pointer FunctionZoom Button Volume ButtonWired Remote Jack Focus ButtonOperating ON-SCREEN Menu HOW to Operate ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Before Operation Menu BAR Turning on Projector Basic OperationTurning on / OFF Projector Turning OFF ProjectorFocus Adjustment Adjusting ScreenZoom Adjustment Keystone AdjustmentBasic Operation Picture Freeze Function Timer FunctionNo Show Function Menu Operation Sound AdjustmentDirect Operation Sound MenuSelecting Computer System Computer InputSelecting Input Source InputAuto Computer Input Automatic MULTI-SCAN SystemSelect Computer System Manually PC System MenuComputer Input Compatible Computer Specifications ResolutionPC Adjust Menu PC AdjustmentAuto PC Adjustment Computer InputComputer Input Manual PC Adjustment Display area H Display areaFull screen Image Level Select Menu Picture Image AdjustmentImage Level Select Direct Image 1~4Computer Input Image Level Adjustment Image Adjust MenuPicture Screen Adjustment Screen MenuWhen Select Input 2 5 BNC Terminal Video InputVideo Input Component Video Signal FormatSelecting Video System PAL / Secam / Ntsc / NTSC4.43 / PAL-M / PAL-NCinema Tint Video Input Image Level AdjustmentColor Progressive scanProvides image at a normal video aspect ratio of 4 Setting Menu SettingSetting Menu To change code of Remote Control Unit To change code of ProjectorLamp counter reset Wireless Mouse modeProjector mode USBInstallation Operating Wireless MouseMaintenance Operating Wireless MouseAppendix AIR Filter Care and Cleaning Cleaning Projection LensAppendix Lamp Management Yellow Lamp Dim Lamp Red Lamp Mark on LampAppendix Lamp Replacement Front Indicators Rear IndicatorsLamp Handling Precautions Troubleshooting Does not work Remote Control UnitWireless Mouse Function does notTechnical Specifications Appendix Configurations of Terminals DVI-I Terminal DIGITAL/ANALOGSerial Port IN/OUT Terminal Appendix Appendix Appendix Key to better communications Canada

LC-UXT3 specifications

The Eiki LC-UXT3 is an advanced multimedia projector that excels in delivering high-quality presentations and engaging visual experiences across various environments. Designed for versatility, it is ideal for educational institutions, corporate offices, and large venues.

One of the standout features of the LC-UXT3 is its impressive resolution. With a WUXGA resolution of 1920 x 1200 pixels, it provides sharp and detailed images that enhance the viewing experience. This high resolution is particularly beneficial for displaying intricate graphics, texts, and videos, making it suitable for both professional and educational use.

The projector boasts a powerful brightness level of 6000 lumens, ensuring vivid images even in well-lit rooms. This high lumen output allows for optimal performance during daytime presentations or in environments where light control is limited. Additionally, the LC-UXT3 features a high contrast ratio, which enhances color accuracy and depth, giving presentations a professional touch.

In terms of connectivity, the Eiki LC-UXT3 excels with multiple input options, including HDMI, VGA, and composite video ports. This versatility allows users to connect a variety of devices such as laptops, tablets, and other multimedia sources seamlessly. Furthermore, the projector supports wireless connectivity, enabling easy interactions with devices without the need for messy cables.

The LC-UXT3 incorporates advanced technology to enhance its performance. With its 3LCD technology, the projector delivers bright and vibrant colors while minimizing the risk of the "rainbow effect" often associated with single-chip projectors. This technology ensures accurate color reproduction, making it perfect for dynamic presentations that require color precision.

Another noteworthy characteristic of the Eiki LC-UXT3 is its extensive range of lens options, which allows for flexible installation setups. The motorized lens shift, zoom, and focus features facilitate easy adjustments, making it an ideal choice for various rooms and setups.

In conclusion, the Eiki LC-UXT3 is a feature-rich multimedia projector that combines high brightness, resolution, and connectivity options, making it an excellent choice for professional and educational settings. Its advanced technologies and flexible installation capabilities make it a reliable tool for any presentation need, ensuring a powerful and engaging visual experience every time.
Top Page Image Contents