Operating instructions
To activate the 640R, switch the Power button on the rear panel to On then press the Standby/On button on the front panel.
Selecting the source
1.Select the desired source by pushing the corresponding source button on the front panel or remote control.
DVD | Video 1 | Video 2 | Recorder 1 | Aux | CD | Recorder 2 | 7.1 Direct |
2.If necessary, press the Audio Input Type button to select the input mode of the source equipment, either analog or digital (depending on the connection made on the rear panel).
| Digital Processing Options |
|
| |
Audio | Stereo | Pro Logic/Neo/ | Dolby Digital/ | Video |
Input Type | Modes | DSP Surround | DTS Surround | Input Type |
|
| Modes | Modes |
|
The digital or analog icons on the display show which is the currently selected input type.
Note: The 640R stores the input type for each source so that it is automatically recalled when that source is selected again.
Selecting the desired listening mode
Select an appropriate mode for the source material/type you are listening to by pressing one of the 3 main Digital Processing Options buttons and cycling through
| Digital Processing Options |
|
| |
Audio | Stereo | Pro Logic/Neo/ | Dolby Digital/ | Video |
Input Type | Modes | DSP Surround | DTS Surround | Input Type |
|
| Modes | Modes |
|
In all cases the first time a mode button is pressed the 640R will report the current decoding mode on the front panel display. Pressing the button again will then cycle to the next available mode (if there is one). If no button is pressed for 4 or 5 seconds the 640R returns to normal operation without changing mode.
Stereo Modes - Selects 2 channel Stereo operation for stereo material, pressing again selects Stereo + Sub mode.
This is a digitally processed mode that allows bass and treble controls, and sub generation if required. The input can be either analog (in which case it will be turned into digital by 24 bit A/D conversion) or natively digital.
Digital inputs can be connected to the SPDIF outputs from Tuner's or CD Players etc (LPCM) or the digital outputs of DVD players (set to Bitstream/Raw) playing
Prologic/Neo:6/DSP modes - Selects a range of surround modes with appropriate matrix encoded material.
These modes are for use with the analog or digital outputs from TV's or VCR Players for instance if the source material has been encoded using one of these processes.
ProLogic and Neo:6 are both available in various guises to decode appropriately encoded soundtracks. Additionally DSP modes are available to process sources with no encoding at all. Due to the matrix encoding process none of these modes incorporate flags that tell the 640R the type of encoding used in the source material. Thus you must manually select these modes.
azur 640R
Dolby Digital EX/DTS ES Modes - Selects a range of digital surround |
| ENGLISH |
modes with the appropriately digitally encoded material (only). These |
| |
|
| |
modes are for use with the digital outputs (set to Bitstream/Raw) from |
|
|
DVD players or satellite receivers etc. In order for the 640R to allow |
|
|
selection of these modes a valid input digital bitstream must be present. |
|
|
|
| |
This is because the 640R needs to read the incoming flags in order to |
|
|
determine the type of decoding which can be used and present any |
|
|
options that might be possible. |
|
|
If no bitstream is present, pressing this button will result in the 640R |
|
|
displaying “Mode Unavailable”. |
|
|
Note: The modes available for each button depend both on the Speaker |
|
|
Configuration that has previously been set in the OSD and on the source |
|
|
material. |
|
|
For 5.1 Speaker setups the Dolby Digital/DTS Surround Modes button |
|
|
will have a maximum of only one mode available which will depend on |
|
|
the source material. See the following ‘Decode modes’ tables. |
|
|
The Prologic/ Neo:6/DSP modes button will present more options where |
|
|
possible including |
|
|
These are modes that allow extra processing to be applied after the |
|
|
main |
|
|
Music. Which adds a 5.1 ProLogic decode to a Stereo Dolby Digital |
|
|
decode to turn 2 channel stereo into 5.1. |
|
|
This mode would be accessed by first selecting the Dolby Digital EX / |
|
|
DTS ES Mode button with a Dolby (2/0) bitstream present (selects a |
|
|
normal Dolby Digital (2/0) decode. Now press the Pro Logic/ Neo:6/DSP |
|
|
mode button to access the next mode which adds a PLII decode on top. |
|
|
For 6.1 or 7.1 Speaker setups, the number of decoding possibilities |
|
|
increases as shown in the following ‘Decode modes’ tables. Several |
|
|
extra Post Processing modes are available using either Prologic IIx or |
|
|
Neo:6. |
|
|
Incoming Dolby Digital/DTS streams are always shown on the front |
|
|
panel display as Dolby Digital (x/x) or DTS (x/x), where the bracketed |
|
|
numbers indicate the active channels in the source material. Active |
|
|
output channels are shown by the icons on the right hand side of the |
|
|
front panel display. Possible incoming DD/DTS types are: |
|
|
(1/0) - Mono, Centre channel only |
|
|
(2/0) - Left/Right stereo |
|
|
(2/1) - Left/Right stereo and LFE (Sub) |
|
|
(2/2) - Left/Right stereo and Left/Right surround |
|
|
(3/0) - Left, Centre, Right |
|
|
(3/1) - Left, Centre, Right and LFE (Sub) |
|
|
(3/2) - 5.1: Left, Right, Centre, Left Surround, Right Surround and LFE |
|
|
(Sub) |
|
|
(3/3) - 6.1: Left, Right, Centre, Left Surround, Right Surround, Surround |
|
|
Back and LFE (Sub) |
|
|
19