Intel MB896 user manual ATX Power on Switch Pins 7, J6 USB5/6 Port Pin Header

Page 23

INSTALLATIONS

ATX Power ON Switch: Pins 7 and 17

This 2-pin connector is an “ATX Power Supply On/Off Switch” on the system that connects to the power switch on the case. When pressed, the power switch will force the system to power on. When pressed again, it will force the system to power off.

Reset Switch: Pins 9 and 19

The reset switch allows the user to reset the system without turning the main power switch off and then on again. Orientation is not required when making a connection to this header.

Hard Disk Drive LED Connector: Pins 10 and 20 This connector connects to the hard drive activity LED on control panel. This LED will flash when the HDD is being accessed.

		Pin #	Signal Name
		10	HDD Active
		20	5V
J6: USB5/6 Port Pin Header
Signal Name	Pin	Pin Signal Name
Vcc	1	5	Ground
D-	2	6	D+
D+	3	7	D-
Ground	4	8	Vcc

MB896 User’s Manual

19

Image 23

Contents Version USER’S ManualAcknowledgments Table of Contents MB896 Mini ITX Motherboard Product Description IntroductionChecklist CPU FSB MB896 SpecificationsIntroduction Board Dimensions Installations Installing the CPU Installing and Removing Memory Modules Installing the MemorySetting the Jumpers Jumper Locations on MB896 JP5 CompactFlash Slave/Master Selection JP3 LCD Panel Power SelectionJP4 Clear Cmos Setting JP2 Pentium M Vcc Voltage SelectionConnectors on MB896 Connector Locations on MB896 CN2 COM1 and VGA Connector CN1 PS/2 Keyboard and PS/2 Mouse ConnectorsFAN2 CPU Fan Power Connector FDD1 Floppy Drive Connector IDE1 IDE ConnectorJ1 IrDA Connector J11 ATX12V ConnectorATX1 ATX Power Supply Connector J2 Digital I/O J3 System Function ConnectorJ6 USB5/6 Port Pin Header ATX Power on Switch Pins 7J7 COM2 Serial Port J9 LCD Backlight SettingJ14 Mini PCI Connector J18 Front Audio Connector J15 Speaker ConnectorJ16 1394 Connector J17 Wake On LAN ConnectorSDVOCCLK+ J20 CD-In Pin HeaderThis page is intentionally left blank Bios Setup Bios Setup Bios IntroductionPhoenix AwardBIOS Cmos Setup Utility Date Standard Cmos SetupDrive a / Drive B TimeIDE Channel Master/Slave Halt On VideoVirus Warning Advanced Bios FeaturesCPU Feature Hard Disk Boot PriorityBoot Up Floppy Seek Quick Power On Self TestFirst/Second/Third Boot Device Boot Other DeviceMPS Version Control for OS Typematic Delay MsecApic Mode Security OptionCAS Latency Time Advanced Chipset FeaturesDram RAS# to CAS# Delay Dram Timing SelectableOn-Chip VGA Setting Precharge Delay tRASSystem Bios Cacheable Video Bios CacheableLAN PXE Option ROM Panel ScalingPanel Number Onboard PCI-E LANOnChip IDE Device Integrated PeripheralsOnChip Primary/Secondary PCI IDE IDE HDD Block ModeIDE DMA Transfer Access On-chip Primary PCI IDE EnabledHot Key Power on On-Chip Serial ATA SettingPower on Function KB Power on PasswordPwron After PWR-Fail Uart Mode SelectOnboard Serial Port Acpi Function Power Management SetupRUN Vgabios if S3 Resume Power ManagementVideo Off Method Suspend ModeHDD Power Down Power On by RingReload Global Timer Events Resume by AlarmPNP/PCI Configurations Bios Setup PC Health Status Spread Spectrum Modulated Frequency/Voltage ControlAuto Detect PCI Clk Save & Exit Setup Load Fail-Safe DefaultsLoad Optimized Defaults Set Supervisor PasswordThis page is intentionally left blank Drivers Installation Click IntelR Chipset Software Installation Utility Intel Chipset Software Installation UtilityDrivers Installation Click IntelR 915GMChipset Family Graphics Driver VGA Drivers InstallationImportant Note Click Realtek AC97 Codec Audio Driver AC97 Codec Audio Driver InstallationClick Install Base Software to continue LAN Drivers InstallationDriver Installation O Port Address Map AppendixLevel Function Interrupt Request Lines IRQSample Code Watchdog Timer ConfigurationAppendix W627EHFBASE = 0x4E result = W627EHFBASE OutportbW627EHFINDEXPORT, W627EHFLOCK Appendix W627EHFLOCK