Intel MB893 user manual Video, Halt On

Page 34

BIOS SETUP

Video

This field selects the type of video display card installed in your system. You can choose the following video display cards:

EGA/VGA

For EGA, VGA, SEGA, SVGA

 

or PGA monitor adapters. (default)

CGA 40

Power up in 40 column mode.

CGA 80

Power up in 80 column mode.

MONO

For Hercules or MDA adapters.

Halt On

This field determines whether or not the system will halt if an error is detected during power up.

No errors

The system boot will not be halted for any error

 

that may be detected.

All errors

Whenever the BIOS detects a non-fatal error,

 

the system will stop and you will be prompted.

All, But Keyboard

The system boot will not be halted for a

 

keyboard error; it will stop for all other errors

All, But Diskette

The system boot will not be halted for a disk

 

error; it will stop for all other errors.

All, But Disk/Key

The system boot will not be halted for a key-

 

board or disk error; it will stop for all others.

30

MB893 User’s Manual

Image 34
Contents USER’S Manual VersionAcknowledgments Table of Contents MB893 Server Motherboard Checklist IntroductionProduct Description Specifications IDEBoard Dimensions Installations Installing the CPU ATX Power Installation Installing the MemorySetting the Jumpers Jumper Locations on MB893 JP5 COM2 J6 Tx/Rx Signal Setting Reserved JP3 Clear Cmos ContentsJP4 CN7 & CN10 LAN By-pass Function Setting JP2 Compact Flash Master/Slave SelectJP7 Connectors on MB893 Connector Locations on MB893 ATX1 ATX Power Supply Connector ATX12V1 ATX 12V Power ConnectorSYSFAN1 System Fan Power Connector CN1 Front Side Bridge Board to ID370CN11 Dual Port USB Connector CN8, CN9 Sata ConnectorCN4 Mini PCI Socket CN12 COM1 Connector J3 USB ConnectorJ5, J6 COM2, COM3 Connectors J4 Parallel Port Connector ReservedJ8 PS/2 Keyboard & Mouse Connectors FDD1 Floppy Drive Connector Reserved IDE1 Primary IDE Connectors 40-pin 2.54mmIDE2 Primary IDE Connectors 44-pin 2.0mm Watchdog Timer Configuration Sample CodeCall LockChip ret EnableAndSetWatchdog Endp Mov dx, 2Eh mov al, 0Aah Out dx, al ret This page is intentionally left blank Bios Setup Bios Introduction Bios SetupPhoenix AwardBIOS Cmos Setup Utility Standard Cmos Setup DateIDE Primary HDDs / IDE Secondary HDDs TimeDrive a / Drive B Video Halt OnHard Disk Boot Priority Advanced Bios FeaturesVirus Warning Boot Other Device Quick Power On Self TestFirst/Second/Third Boot Device Boot Up Floppy SeekTypematic Delay Msec Boot Up NumLock StatusTypematic Rate Setting Apic ModeConsole Redirection Agent After BootOS Select for Dram 64MB Baud RateAdvanced Chipset Features Memory Hole At 15M-16M System Bios CacheableSystem Memory Frequency On-Chip Frame Buffer Size MemoryIntegrated Peripherals IDESata Mode IDE HDD Block ModeIDE DMA Transfer Access OnChip Primary/Secondary PCI IDEKB Power on Password Pata IDE ModePower on Function Hot Key Power onOnboard Serial/Parallel Port Uart Mode SelectOnboard FDC Controller Pwron After PWR-FailAcpi Function Power Management SetupPower Management Video Off MethodPower On by Ring Suspend ModeHDD Power Down Resume by AlarmReload Global Timer Events PNP/PCI Configurations Temperatures/Fan Speeds/Voltages CPU Warning TemperatureShutdown Temperature PC Health StatusLevel2 Temperature 1st Smart Fan II Temperature SYSFAN1 connector2nd Smart Fan II Temperature CPUFAN1 / CPUFAN2 Third phase Smart FAN functionalityAuto Detect PCI Clk Frequency/Voltage ControlCPU Clock Ratio Spread SpectrumSet Supervisor/User Password Load Fail-Safe DefaultsLoad Setup Defaults Save & Exit SetupDrivers Installation Intel 915G Chipset Software Intallation Utility Intel 915G Chipset Graphics Driver Marvell 88E8053 LAN Drivers Installation Intel PRO LAN Drivers Installation This page is intentionally left blank Appendix O Port Address MapInterrupt Request Lines IRQ Level Function