Intel AIMB-253 user manual FCC-B Radio Frequency Interference Statement

Page 4

FCC-B Radio Frequency Interference Statement

This equipment had been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio fre- quency energy and, if not installed and used in accor- dance with the instructions, may cause harmful interference to radio com- munications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turn- ing the equipment off and on, the user is encouraged to try to correct the interference by one or more of the measures listed below.

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/television technician for help.

Notice 1

The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Notice 2

Shielded interface cables and A.C. power cord, if any, must be used in order to comply with the emission limit.

AIMB-253 User Manual

iv

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Mini-ITX AIMB-253 Series Intel Core 2 Duo/Core Duo/ Core Solo Mini ITX Main BoardCopyright Notice TrademarksRevision History Technical SupportSafety Instructions OpeningsFCC-B Radio Frequency Interference Statement Page English Weee Waste Electrical and Electronic Equipment StatementContents Chapter Bios Setup PC Health Page Getting Started Mainboard Specifications Slots ConnectorsForm Factor Mounting Mainboard LayoutEnvironmental Hardware Setup Quick Components Guide Quick Components GuideCPU & Cooler Set Installation CPU Central Processing UnitOnly and may differ from the actual look of your mainboard Hardware Setup Installing Ddrii Modules MemoryATX 20-Pin System Power Connector ATX1 Power SupplyATX1 Pin Definition Back Panel LAN RJ-45 Jack LAN RJ-45 JackChassis Intrusion Switch Connector JCI1 Connectors2 44-Pin Eide Connector IDE1 Audio Amplifier Connector JAMP1 Serial ATA Connectors SATA1, SATA2JAMP1Pin Definition Front Audio Connector JAUD1 JAUD1 Pin DefinitionFan Power Connectors CPUFAN1, SYSFAN1 Fan Power Connectors CPUFAN1, SYSFAN1Front Panel Connector JFP1 JFP1 Pin DefinitionSerial Port Connector J2 COM2 COM3PIN Signal J2 Pin DefinitionFront USB Connector FUSB2 FUSB2 Pin DefinitionDigital IO Connector J3 J3 Pin DefinitionParallel Port Header JLPT1 14 Parallel Port Header JLPT1Lvds Flat Panel Connector JLVDS1 10 Lvds Connector JLVDS1Tune the Lvds backlight in the Bios Setup Utility Lvds Power Selection Jumper J1 COM Port Power Jumpers JCOMP4, JCOMP511 Lvds Power Selection Jumper J1 JumpersClear Cmos Jumper CLRCMOS1 Slots PCI Peripheral Component Interconnect Express SlotPCI Peripheral Component Interconnect Slot PCI Interrupt Request RoutingBios Setup Entering Setup Press Delete to enter SetupGetting Help Control KeysControl Keys Menu Bar Main ExitDate mmddyy Time hhmmssHalt On Base/Extended/Total MemoryAdvanced Advanced Bios Features Quick Power On Self TestBoot Up NumLock Status Typematic Rate SettingTypematic Delay Msec Apic ModeAdvanced Chipset Features Typematic Rate Chars/SecDram RAS# to CAS# Delay Precharge Delay tRASVGA Setting Dram Timing SelectableBoot Display On-Chip Frame Buffer SizeLvds Panel Type Lvds Backlight ControlOn-Chip Serial ATA Setting Pata Eide Mode / Sata PortEide Primary Master/Slave PIO Eide Primary Master/Slave UdmaOnboard Device USB ControllerUSB 2.0 Controller USB Keyboard/Mouse SupportOnboard LAN1/ LAN2 Boot ROM Amplifier dBOnboard Ethernet #1/ #2 Super IO DeviceSerial Port Setting Serial Port 2 / 3 ModeOnboard Serial Port 1 / 2 / 3 / 4 Serial Port 1 / 2 / 3 / 4 / 5 Use IRQPower Management Setup Acpi FunctionPower On by Ring Resume By AlarmAcpi Suspend Type Soft-Off by PWR-BTTNDate of Month Alarm Time hhmmss AlarmPC Health Pwron After PWR-FailSmart Fan Setting 11 Smart Fan SettingSmart System / CPU Fan Temp System / CPU Temp ToleranceSet Supervisor Password Set User PasswordSecurity Security OptionSystem 13 SystemBoot Hard Disk Boot PriorityFirst / Second / Third Boot Device Boot Other DeviceLoad Fail-Safe Defaults Load Optimized DefaultsSave & Exit Setup Exit

AIMB-253 specifications

The Intel AIMB-253 is a versatile and robust industrial motherboard designed to meet the demands of a variety of applications, particularly those in the embedded and industrial computing landscape. This motherboard is engineered to support Intel's 6th and 7th generation Core processors, which provide a notable performance boost and increased efficiency compared to their predecessors.

One of the standout features of the AIMB-253 is its compact form factor, which allows for seamless integration into constrained spaces, making it ideal for applications such as kiosks, digital signage, and automation systems. The motherboard's dimensions are suitable for standard industrial enclosures, facilitating easy deployment in various environments.

The AIMB-253 boasts advanced graphics capabilities thanks to its support for Intel HD Graphics. This integrated solution enables high-quality visual output, making the motherboard suitable for applications requiring significant graphical processing, such as video surveillance or multimedia playback. Additionally, the inclusion of multiple display outputs, including HDMI and DisplayPort, allows for flexible display configurations.

In terms of connectivity, the AIMB-253 is equipped with a rich set of I/O interfaces, including multiple USB ports, COM ports, and Ethernet connections. These features enable seamless connectivity with various peripherals and network devices, enhancing its functionality in industrial automation and control applications. The board also supports dual SATA III interfaces for high-speed data storage solutions, ensuring ample storage capacity and performance.

Robustness and reliability are critical in industrial settings, and the AIMB-253 does not disappoint. It is designed to operate in a wide temperature range, making it suitable for various environmental conditions. Furthermore, the motherboard supports wide voltage input, enhancing its adaptability for different power supply scenarios.

The AIMB-253 also incorporates Intel's advanced technologies, such as Intel vPro, which provides secure remote management capabilities. This feature is especially beneficial in enterprise environments where remote access and system management are critical for maintaining operational efficiency.

Overall, the Intel AIMB-253 is a powerful, versatile, and reliable industrial motherboard that combines high performance with advanced connectivity options and robust build quality, making it an excellent choice for a range of embedded and industrial applications.
Top Page Image Contents