Intel AIMB-253 user manual Main, Exit, Date mmddyy, Time hhmmss, Eide Channel 0/1/2/3 Master/Slave

Page 43

Exit

This menu allows you to load the BIOS default values or factory default settings into the BIOS and exit the BIOS setup utility with or without changes.

3.3 Main

Figure 3.2: The Main Menu

Date (mm:dd:yy)

The date format is <Day>, <Month> <Date> <Year>.

Time (hh:mm:ss)

The time format is <Hour> <Minute> <Second>.

EIDE Channel 0/1/2/3 Master/Slave

Press PgUp/<+> or PgDn/<-> to select [Manual], [None] or [Auto] type. Note that the specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information for this category. If your hard disk drive type is not matched or listed, you can use [Manual] to define your own drive type manually.

33

Chapter 3 BIOS Setup

Image 43
Contents Intel Core 2 Duo/Core Duo/ Core Solo Mini ITX Main Board Mini-ITX AIMB-253 SeriesTechnical Support Copyright NoticeTrademarks Revision HistoryOpenings Safety InstructionsFCC-B Radio Frequency Interference Statement Page Weee Waste Electrical and Electronic Equipment Statement EnglishContents Chapter Bios Setup PC Health Page Getting Started Mainboard Specifications Slots ConnectorsForm Factor Mounting Mainboard LayoutEnvironmental Hardware Setup Quick Components Guide Quick Components GuideCPU Central Processing Unit CPU & Cooler Set InstallationOnly and may differ from the actual look of your mainboard Hardware Setup Memory Installing Ddrii ModulesATX 20-Pin System Power Connector ATX1 Power SupplyATX1 Pin Definition Back Panel LAN RJ-45 Jack LAN RJ-45 JackChassis Intrusion Switch Connector JCI1 Connectors2 44-Pin Eide Connector IDE1 Audio Amplifier Connector JAMP1 Serial ATA Connectors SATA1, SATA2JAMP1Pin Definition JAUD1 Pin Definition Front Audio Connector JAUD1Fan Power Connectors CPUFAN1, SYSFAN1 Fan Power Connectors CPUFAN1, SYSFAN1JFP1 Pin Definition Front Panel Connector JFP1COM2 COM3 Serial Port Connector J2J2 Pin Definition PIN SignalFUSB2 Pin Definition Front USB Connector FUSB2J3 Pin Definition Digital IO Connector J314 Parallel Port Header JLPT1 Parallel Port Header JLPT110 Lvds Connector JLVDS1 Lvds Flat Panel Connector JLVDS1Tune the Lvds backlight in the Bios Setup Utility Jumpers Lvds Power Selection Jumper J1COM Port Power Jumpers JCOMP4, JCOMP5 11 Lvds Power Selection Jumper J1Clear Cmos Jumper CLRCMOS1 PCI Interrupt Request Routing SlotsPCI Peripheral Component Interconnect Express Slot PCI Peripheral Component Interconnect SlotBios Setup Press Delete to enter Setup Entering SetupGetting Help Control KeysControl Keys Menu Bar Time hhmmss MainExit Date mmddyyBase/Extended/Total Memory Halt OnAdvanced Typematic Rate Setting Advanced Bios FeaturesQuick Power On Self Test Boot Up NumLock StatusTypematic Rate Chars/Sec Typematic Delay MsecApic Mode Advanced Chipset FeaturesDram Timing Selectable Dram RAS# to CAS# DelayPrecharge Delay tRAS VGA SettingLvds Backlight Control Boot DisplayOn-Chip Frame Buffer Size Lvds Panel TypeEide Primary Master/Slave Udma On-Chip Serial ATA SettingPata Eide Mode / Sata Port Eide Primary Master/Slave PIOUSB Keyboard/Mouse Support Onboard DeviceUSB Controller USB 2.0 ControllerSuper IO Device Onboard LAN1/ LAN2 Boot ROMAmplifier dB Onboard Ethernet #1/ #2Serial Port 1 / 2 / 3 / 4 / 5 Use IRQ Serial Port SettingSerial Port 2 / 3 Mode Onboard Serial Port 1 / 2 / 3 / 4Acpi Function Power Management SetupSoft-Off by PWR-BTTN Power On by RingResume By Alarm Acpi Suspend TypePwron After PWR-Fail Date of Month AlarmTime hhmmss Alarm PC Health11 Smart Fan Setting Smart Fan SettingSystem / CPU Temp Tolerance Smart System / CPU Fan TempSecurity Option Set Supervisor PasswordSet User Password Security13 System SystemBoot Other Device BootHard Disk Boot Priority First / Second / Third Boot DeviceExit Load Fail-Safe DefaultsLoad Optimized Defaults Save & Exit Setup