Tascam CD-A500 user service Important Safety Instructions

Page 2

IMPORTANT SAFETY INSTRUCTIONS

CAUTION:

ORead all of these Instructions.

OSave these Instructions for later use.

OFollow all Warnings and Instructions marked on the audio equipment.

1)Read Instructions — All the safety and operating instructions should be read before the product is operated.

2)Retain Instructions — The safety and operating instructions should be retained for future reference.

3)Heed Warnings — All warnings on the product and in the operating instructions should be adhered to.

4)Follow Instructions — All operating and use instructions should be followed.

5)Cleaning — Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

6)Attachments — Do not use attachments not recommended by the product manufacturer as they may cause hazards.

7)Water and Moisture — Do not use this product near water _ for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.

8)Accessories — Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the man- ufacturer’s instructions, and should use a mounting accessory recom- mended by the manufacturer.

9)A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

10)Ventilation — Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

11)Power Sources — This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.

12)Grounding or Polarization — This product may be equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your elec- trician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

13)Power-Cord Protection Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, conve- nience receptacles, and the point where they exit from the product.

14)Outdoor Antenna Grounding — If an outside antenna or cable sys- tem is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of anten- na-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

"Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Section 820-40 of the NEC which provides guidelines for proper ground- ing and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

Example of Antenna Grounding as per

National Electrical Code, ANSI/NFPA 70

 

ANTENNA

 

LEAD IN

 

WIRE

 

GROUND

 

CLAMP

 

ANTENNA

 

DISCHARGE UNIT

 

(NEC SECTION 810-20)

ELECTRIC

 

SERVICE

GROUNDING CONDUCTORS

EQUIPMENT

 

(NEC SECTION 810-21)

 

GROUND CLAMPS

 

POWER SERVICE GROUNDING

 

ELECTRODE SYSTEM

NEC - NATIONAL ELECTRICAL CODE

(NEC ART 250. PART H)

 

15)Lightning — For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable sys- tem. This will prevent damage to the product due to lightning and power- line surges.

16)Power Lines — An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power cir- cuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

17)Overloading — Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in risk of fire or elec- tric shock.

18)Object and Liquid Entry — Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

19)Servicing — Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

20)Damage Requiring Service — Unplug this product from the wall outlet and refer servicing to qualified service personnel under the follow- ing conditions:

a) when the power-supply cord or plug is damaged.

b) if liquid has been spilled, or objects have fallen into the product. c) if the product has been exposed to rain or water.

d) if the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation.

e) if the product has been dropped or damaged in any way.

f ) when the product exhibits a distinct change in performance _ this indi- cates a need for service.

21)Replacement Parts — When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other haz- ards.

22)Safety Check — Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to deter- mine that the product is in proper operating condition.

23)Wall or Ceiling Mounting — The product should be mounted to a wall or ceiling only as recommended by the manufacturer.

24)Heat — The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

_ 2 _

Image 2
Contents CD-A500 Important Safety Instructions Wavelength 760 800nm Optical pickup Type KSS-212BManufacturer Sony Corporation Laser output Before Use Rack mounting ConnectionsVoltage Conversion PREPEAT 1/ALL button aPROGRAM button sSHUFFLE button Name of Each ControlWCD Sync button eRECORD button rREC Mute button VINTRO Check button bAUTO Space button nA-B buttonBasic Operation ∑ Music search using Search buttons /ÒCD Player ∑ Even if the disc tray is openProgram Playback ∑ To review the program contents∑ To cancel a programmed track ∑ Programming required tunesRepeat Function ∑ To repeat a designated section A-B Repeat modeRandom Playback ∑ Programmed repeat playbackSingle Playback Time Counter DisplayAuto Spacing Intro Check FunctionRecording Cassette Deck OperationPlayback ErasingPitch Control How to Select Any Required Tune Using CPSRTZ Return To Zero Function Fast Wind∑ To record from any desired posi- tion of the tape Copying from CD to Tape∑ To record from the beginning of the tape Timer-controlled operation ∑ Timer RecordingCD player TroubleshootingGeneral Cassette deckMaintenance SpecificationsTo the User