Intel GA-8N-SLI PRO USB Keyboard Support, USB Mouse Support, AC97 Audio, Onboard SATAII/IDE3

Page 44

English

USB Keyboard Support

Enabled	Enable USB keyboard support.
Disabled	Disable USB keyboard support. (Default value)
USB Mouse Support
Enabled	Enable USB mouse support.
Disabled	Disable USB mouse support. (Default value)
AC97 Audio
Auto	Autodetect onboard AC'97 audio function. (Default value)
Disabled	Disable this function.
Onboard LAN2 Function (Marvell 88E1111/88E1115)
(For the GA-8N-SLI Pro/GA-8N-SLI motherboard, the item is Onboard LAN Function)
Auto	Autodetect onboard LAN2 chip function.(Default value)
Disabled	Disable onboard LAN2 chip function.
Onboard SATAII/IDE3
Enabled	Enable onboard SATAII/IDE3 function.(Default value)
Disabled	Disable onboard SATAII/IDE3 function.
Onboard SATAII/IDE3 Mode
RAID	Set onboard SATAII/IDE3 to RAID mode.
BASE	Set onboard SATAII/IDE3 to BASE (ATA) mode.(Default value)
Onboard 1394b Function
Enabled	Enable onboard IEEE1394b function.(Default value)
Disabled	Disable onboard IEEE1394b function.
Onboard LAN Function (Marvell 8053)
Enabled	Enable onboard LAN chip function. (Default value)
Disabled	Disable onboard LAN chip function.
Onboard Serial Port 1
Auto	BIOS will automatically setup the port 1 address.
3F8/IRQ4	Enable onboard Serial port 1 and address is 3F8/IRQ4. (Default value)
2F8/IRQ3	Enable onboard Serial port 1 and address is 2F8/IRQ3.
3E8/IRQ4	Enable onboard Serial port 1 and address is 3E8/IRQ4.
2E8/IRQ3	Enable onboard Serial port 1 and address is 2E8/IRQ3.
Disabled	Disable onboard Serial port 1.
i-Lock
Enabled	Enable the i-Lock function. (Default value)
Disabled	Disable the i-Lock function.
Onboard Parallel Port
Disabled	Disable onboard LPT port.
378/IRQ7	Enable onboard LPT port and address is 378/IRQ7. (Default value)
278/IRQ5	Enable onboard LPT port and address is 278/IRQ5.
3BC/IRQ7	Enable onboard LPT port and address is 3BC/IRQ7.
Parallel Port Mode
SPP	Using Parallel port as Standard Parallel Port. (Default value)
EPP	Using Parallel port as Enhanced Parallel Port.
ECP	Using Parallel port as Extended Capabilities Port.
ECP+EPP	Using Parallel port as ECP and EPP mode.
Only for GA-8N-SLI Royal.		Only for GA-8N-SLI Pro.
P4 nForce4 SLI Series Motherboard		- 44 -

Image 44

Contents GA-8N-SLI Motherboard GA-8N-SLI Pro June 2 GA-8N-SLI Copyright Product Manual ClassificationTable of Contents Drivers Installation 8N-SLI Royal Pro/GA-8N-SLI DDRII1 DDRII2 DDRII3 DDRII4PCI-ECLK LANTSB82AA2 TSB81BA3 Codec 2PCI PciclkPage Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary CPURAID BiosALC850 Codec HT functionality requirement content Installation of the CPU and HeatsinkInstallation of the CPU Installation of the Heatsink Installing/Removing Cool-Plus Northbridge Cooling Fan Installation of MemoryDual Channel DDR Installation of Expansion Cards Installation of U-Plus DPS Universal Plus Dual Power System How to install U-Plus DPS?Setup of SLI Scalable Link Interface Configuration SLI bridge connector GC-SLICONSLI switch module GC-SLISW-C19 SLI switch module GC-SLISW-3D1English Graphics card I/O Back Panel Introduction Side Speaker Out Connectors IntroductionCenter/Subwoofer Speaker Out ATX12V/ATX Power Connector 5 Cpufan / SYSFAN/ Pwrfan Cooler Fan Power Connector Nbfan Chip Fan Power ConnectorFDD Floppy Connector IDE1/IDE2/IDE3 IDE ConnectorPwrled Fpanel Front Panel Jumper Faudio Front Audio Connector Cdin CDUSB1 / FUSB2 / FUSB3 Front USB Connector Spdifin Spdif17 F11394/F21394 Ieee 1394 Connectors Clrcmos Clear CmosPCIE12V Power Connector CI Chassis Intrusion, Case OpenBATBattery RfidStatus Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. GA-8N-SLI Royal F3l „ Load Fail-Safe Defaults „ Load Optimized Defaults„ Set Supervisor Password „ Set User PasswordIDE Channel 0 Master/Slave IDE Channel 1 Master/Slave Standard Cmos FeaturesTime Floppy 3 Mode Support for Japan Area Drive a / Drive BHalt on MemoryAdvanced Bios Features Hard Disk Boot PriorityFirst / Second / Third Boot Device ROM Boot PriorityPassword Check CPU Hyper-ThreadingLimit Cpuid Max. to No-Execute Memory Protect NoteIntegrated Peripherals BaseIDE Secndry Slave RAID Sataii 1 Primary RAIDSataii 1 Secondary RAID Sataii 2 Primary RAIDOnboard SATAII/IDE3 Mode Parallel Port ModeUSB Keyboard Support USB Mouse SupportPower Management Setup Power-On by AlarmPME Event Wake Up Modem Ring OnPower On By Mouse Power On By KeyboardKB Power on Password AC Back FunctionPnP/PCI Configurations PCI 1 IRQ AssignmentPC Health Status PWM CPU Smart FAN ModeCPU Smart FAN Control MB Intelligent TweakerM.I.T M. NoteCPU Clock RatioNote A.2FSB Turbo Mode System Clock ModeNew FSB Speed QDR Current FSB Speed QDRFSB OverVoltage Control Sataii OverVoltage ControlCPU Voltage Control Normal CPU VcoreSelect Language Load Fail-Safe DefaultsLoad Optimized Defaults Set Supervisor/User Password Save & Exit Setup Exit Without SavingP4 nForce4 SLI Series Motherboard Drivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish Unique Software Utilities EasyTune 5 Introduction User Interface OverviewSystem requirements Xpress Recovery2 IntroductionHow to use the Xpress Recovery2 Limitations Main Screen of Xpress Recovery2Precautions How to use Dual Bios and Q-Flash Utility? Flash Bios Method IntroductionWhat is Dual Bios Technology? Wide Range Protection DisableDefault, Enable Boot From Main BIOSDefault, Backup BiosAuto Recovery EnableDefault, Disable Halt On Error DisableDefault, EnableMethod 1 Q-FlashTMUtility Before You BeginExploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen EnglishCongratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Serial ATA Bios Setting Utility Introduction RAID LevelsConfiguring the Nvidia RAID Bios Entering the RAID Bios SetupUsing the Define a New Array Window Selecting the RAID ModeSelecting the Striping Block Size Assigning the DisksCompleting the RAID Bios Setup English Configuring the Promise PDC20779 RAID Bios Main MenuCreate Arrays Automatically Create Arrays Manually Define Array MenuView Drive Assignments View/Change Drives AssignmentsDelete an Array Delete Array MenuInstalling the RAID drivers Cd bootdrv MenuIntroduction of audio connectors Stereo Speakers Connection and Settings5 2- / 4- / 6- / 8- Channel Audio Function Introduction StepChannel Audio Setup English Step Troubleshooting AMI Bios Beep CodesEnglish Appendix English Contact Us Taiwan HeadquartersChina Shanghai