Intel 8S661FXMP-RZ user manual Integrated Peripherals

Page 27

Integrated Peripherals

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Integrated Peripherals

	IDE1 Conductor Cable	[Auto]	Item Help
	IDE2 Conductor Cable	[Auto]
			Menu Level X
	On-Chip Primary PCI IDE	[Enabled]
			[Auto]
	On-Chip Secondary PCI IDE	[Enabled]
			Auto-detect IDE cable type
	AC97 Audio	[Enabled]

	Onboard LAN device	[Enabled]	[ATA66/100/133]
	USB Controller	[Enabled]
			Set Conductor cable to
	USB Legacy Support	[Disabled]
			ATA66/100/133
	SiS Serial ATA Controller	[Enabled]
			(80 pins)
	SiS Serial ATA Mode	[RAID]

	Onboard Serial Port 1	[3F8/IRQ4]	[ATA33]
	Onboard Serial Port 2	[2F8/IRQ3]
			Set Conductor cable to
	Onboard Parallel Port	[378/IRQ7]
			ATA33(40 pins)
	Parallel Port Mode	[ECP]
	ECP Mode Use DMA	[3]

KLJI: Move	Enter: Select	+/-/PU/PD: Value	F10: Save	ESC: Exit	F1: General Help
F5: Previous Values		F6: Fail-Safe Defaults		F7: Optimized Defaults

IDE1 Conductor Cable

Auto	BIOS autodetects IDE1 conductor cable .(Default Value)
ATA66/100/133	Set IDE1 Conductor Cable to ATA66/100/133 (please make sure your IDE
	device and cable is compatible with ATA66/100/133).
ATA33	Set IDE1 Conductor Cable to ATA33 (please make sure your IDE device and
	cable is compatible with ATA33).

IDE2 Conductor Cable

Auto	BIOS autodetects IDE2 conductor cable. (Default Value)
ATA66/100/133	Set IDE2 Conductor Cable to ATA66/100/133 (please make sure your IDE
	device and cable is compatible with ATA66/100/133).
ATA33	Set IDE2 Conductor Cable to ATA33 (please make sure your IDE device and
	cable is compatible with ATA33).

On-Chip Primary PCI IDE

Enabled	Enable onboard 1st channel IDE port. (Default value)
Disabled	Disable onboard 1st channel IDE port.

On-Chip Secondary PCI IDE

Enabled	Enable onboard 2nd channel IDE port. (Default value)
Disabled	Disable onboard 2nd channel IDE port.

AC97 Audio

Enabled	Enable onboard AC'97 audio function. (Default value)
Disabled	Disable this function.

English


- 27 -	BIOS Setup

Image 27

Contents 8S661FXMP-RZ Motherboard 8S661FXMP-RZ Preparing Your Computer Installing the motherboard to the chassisTable of Content Introduction Features SummaryEnglish 8S661FXMP-RZ 8S661FXMP-RZ Motherboard LayoutBlock Diagram Step Hardware Installation ProcessCPU Installation Install memory modules Install I/O Peripherals Cables Install expansion cardsLine Out Front Speaker Out 11 13LAN Port LineATX12V/ATX Power Connector Cpufan CPU FAN ConnectorSysfan System FAN Connector FDD Floppy ConnectorIDE1/ IDE2 IDE1/IDE2 Connector Fpanel 2x10 pins connector SATA0/SATA1 Serial ATA Connector, Controlled by SiS964Faudio Front Audio Panel Connector BAT BatterySpdifio Spdif In/Out Cdin CD In ConnectorUSB1 / FUSB2 Front USB Connectors Comb Comb ConnectorCI Chassis Intrusion, Case Open Clrcmos Clear Cmos Main Menu Main Menu For example Bios Ver. E2Entering Bios Setup Status Page Setup Menu / Option Page Setup MenuLoad Fail-Safe Defaults Advanced Bios FeaturesPower Management Setup PnP/PCI ConfigurationIDE Channel 0 Master, Slave / IDE Channel 1 Master, Slave Standard Cmos FeaturesDate TimeMemory Floppy 3 Mode Support for Japan AreaDrive a / Drive B Halt onBoot Up Floppy Seek Advanced Bios FeaturesHard Disk Boot Priority First / Second / Third Boot DeviceInit Display First Password CheckCPU Hyper-Threading Limit Cpuid Max. toIntegrated Peripherals USB Legacy Support SiS Serial ATA ModeOnboard LAN device USB ControllerAcpi Suspend Type Power Management SetupParallel Port Mode ECP Mode Use DMAPower LED in S1 state Power On by KeyboardPower On by Mouse Resume by AlarmPCI 3 IRQ Assignment PnP/PCI ConfigurationsPCI 1 IRQ Assignment PCI 2 IRQ AssignmentPC Health Status MB Intelligent Tweaker M.I.T AGP Clock MHz CPU Clock MHzDram Clock MHz AGP/PCI Clock ControlLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupPictures below are shown in Windows XP Install DriversItem Description Taiwan Headquarters Contact UsChina Shanghai