Intel GA-4MXSV user manual Item Checklist, Installing the motherboard to the chassis…

Page 4

GA-4MXSV Motherboard

Item Checklist

The GA-4MXSV motherboard

Serial ATA cable x 4

IDE (ATA100 ) cable x 1 / Floppy cable x 1

I/O Shield Kit

CD for motherboard driver & utility

 

GA-4MXSV user’s manual

 

WARNING!

Computer motherboards and expansion cards contain very delicate Integrated Circuit (IC) chips. To protect them against damage from static electricity, you should follow some precautions whenever you work on your computer.

1. Unplug your computer when working on the inside.

2. Use a grounded wrist strap before handling computer components. If you do not have one, touch both of your hands to a safely grounded object or to a metal object, such as the power supply case.

3. Hold components by the edges and try not touch the IC chips, leads or connectors, or other components.

4. Place components on a grounded antistatic pad or on the bag that came with the components whenever the components are separated from the system.

5. Ensure that the ATX power supply is switched off before you plug in or remove the ATX power connector on the motherboard.

Installing the motherboard to the chassis…

If the motherboard has mounting holes, but they don’t line up with the holes on the base and there are no slots to attach the spacers, do not become alarmed you can still attach the spacers to the mounting holes. Just cut the bottom portion of the spacers (the spacer may be a little hard to cut off, so be careful of your hands). In this way you can still attach the motherboard to the base without worrying about short circuits. Sometimes you may need to use the plastic springs to isolate the screw from the motherboard PCB surface, because the circuit wire may be near by the hole. Be careful, don’t let the screw contact any printed circuit write or parts on the PCB that are near the fixing hole, otherwise it may damage the board or cause board malfunctioning.

4

Image 4
Contents USER’S Manual Table of Content Appendix Item Checklist Installing the motherboard to the chassis…Features Summary IntroductionBios GA-4MXSV Motherboard Layout G HIntel 82573V GbE Hardware Installation Process StepInstalling Processor and CPU Haet Sink Installing CPUInstalling Heat Sink Install memory modules Installation Steps Install expansion cards Connect ribbon cables, cabinet wires, and power supply I/O Back Panel IntroductionLAN LED Description Connectors & Jumper Setting Introduction ATX ATX Power Connector ATX12V +12V Power ConnectorIDE1 IDE Connector FDC1 Floppy ConnectorFPanel1 2X9 Pins Front Panel connector Pin No Signal Name DescriptionUSB2 Front USB Connector COM2J / K SATA1/ 2/ 3/ 4 Serial ATA Connectors WOL1 Wake on LANUF1 CPU Fan Connector WOR1 Wake on RingQ / R UF2/3/4/5 System Fan Connectors Clrcmos Clear Cmos FunctionRecovery Bios Recovery Function Please remove the jumper when system reboot next timeBAT1 Battery Bios Setup Status Page Setup Menu / Option Page Setup Menu BootMainMenu MainSystem Time System DateHard Disk Pre-Delay Legacy Diskette A/BBit I/O TypeAdvanced Processor Options Processor ResetAdvanced Processor Option No Execute Mode Mem. Protection C1 Enhanced ModeProcessor Power Management Advanced About This Section AdvancedMemory Configuration Installed Memory/Available to OS/DIMMGroup 1,2,3,4 StatusMemory Reset Extend RAM StepPCI Configuration EmbeddedNIC#1Onboard LAN1 Control Option ROM ScanEnabled PCI Slot 1/2/3/4/5 Option ROMDevice Configuration I/O Device ConfigurationSerial Port a Serial Port BPS/2 Mouse Parallel PortUSB Controller USB 2.0 Controller Legacy USB SupportRoute Port 80h cycles to Parallel ATA` Native Mode Operation ` Sata Controller Mode Option` Sata Ahci Enable ` Sata RAID EnableEnable MultimediaTimer Advanced Chipset ControlPCI Express Sub-Menu PCIDeviceWake On LAN / PME Wake On RTC AlarmWake On Ring CPU / Motherboard/AmbitTemperature This Menu will disappear when BMC module is populatedHardware Monitor Voltage Monitor 3V Dual, VCC3, VCC, 12V2, 12V1, VBAT, 5VSBBoot -time Diagnostic Reset ConfigurationDataMemory Processor Error Multiprocessor SpecificationSet User Password About This Section SecuritySet Supervisor Password Password on bootFixed disk boot sector Diskette accessServer System Management Server ManagementBios Redirection Port Console RedirectionBaud Rate TerminalTypeFlowControl Console ConnectContinue C.R. after Post EventLogConfugurationPost Error Pause Mini BMC FunctionMini BMC SEL View Log Post System EventEvent Log Viewer System Fan 1/2/3/4/5/6 Error Voltage ErrorBTemperature Error Set ThresholdBoot Priority Order About This Section BootKey used to view ot configure devices Exit About This Section ExitExit Saving Changes Exit Discarding ChangesLoad SettupDefault Discard ChangesSave Changes Technical Reference Intel Chipset Software Installation Utilities Installation ProceduresAuto Run window Setup Wizard License AggremmentInstallation Completed Installation Wizard License Agreement Intel LAN Driver InstallationAuto Run window Intel LAN Drivers Installation Progress Install Option Start InstallationInstallation Complete Auto Run window Host RAID Driver Intel Host RAID Driver InstallationStarting make a driver disk Formatting and writing in floppy sidk VGA ES1000 Driver Installation License Aggremment Installation CompleteDirectX 9.0 Driver Installation Starting InstallaitonInstallaiton Wizard completed Auto Run window License AgreementAppendix AcronymsIoapic