Rear panel connections

1Power On/Off

Switches the unit on and off.

2AC power socket

Once you have completed all connections to the amplifier, plug the AC power cable into an appropriate mains socket then switch on. Your amplifier is now ready for use.

3Loudspeaker terminals

Two sets of loudspeaker terminals are available, A (main loudspeaker terminals) and B (secondary loudspeaker terminals). Both sets of speakers can be turned on and off independently. Connect the wires from your left channel loudspeaker to the LEFT + & - terminals, and the wires from the right channel loudspeaker to the RIGHT + & - terminals. In each case, the red terminal is the positive output and the black terminal is the negative output.

Care should be taken to ensure no stray strands of wire short the speaker outputs together. Please ensure that the loudspeaker terminals have been tightened completely to provide a good electrical connection. It is possible for the sound quality to be affected if the screw terminals are loose.

Note: When using one pair of speakers, use speakers with a nominal impedance of between 4-8 ohms. When using two pairs of speakers, use speakers with a nominal impedance of between 6-8 ohms. Please also note that when multiple speakers are connected across the amplifier’s outputs, the load (as seen by the amplifier) is reduced. This will make the amplifier work harder, and hotter!

4IR (Infrared) Emitter In

Allows modulated IR commands from multi-room systems to be received by the amplifier. Commands received here are not looped out of the Control Bus. Refer to the ‘Custom installation’ section for more information.

5Control Bus

In - Allows un-modulated commands from multi-rooms systems or other components to be received by the unit.

Out - Loop out for control bus commands to another unit. Also allows the 840A V2 to control some Cambridge Audio units.

6RS232C

The RS232C port allows external serial control of the 840A V2 for custom install use. A full command set is available on the Cambridge Audio website at www.cambridge-audio.com. This port can also be used by Cambridge Audio service personnel for software updates.

7A-BUS™ Ready / Incognito Ready™ multi-room outputs

PSU - Connect an Incognito PS5 to supply power to the connected multi-room keypads/speakers.

Keypad 1/2 - Connect one or two Incognito A-BUS KP10 keypads (or other A-BUS compatible keypads) using CAT-5/5e cable. Incognito AS10 Active Ceiling Speakers can also be connected here.

azur 840A V2

			8	ENGLISH
4	5	6	Input 1 Balanced Audio
4	5	6	7
			GND	9
	L			L
	12	11	10
	R			R

Input 1

(Unbalanced)

IR - Four IR outputs for remote control of source equipment.

Please refer to the ‘Multi-Room’ section of this manual for more information on connections and set-ups.

8Input 1 Balanced Audio

Input 1 features either unbalanced (phono/RCA) or balanced (XLR) connections. Either type may be used but not both at the same time. The balanced connection is the higher quality option and can reject noise and interference in the cable when used with other equipment that supports this function. An XLR connector is wired Pin 1 - Ground; Pin 2 - Hot (in-phase); Pin 3 - Cold (phase-inverted).

Use the Balanced/Unbalanced switch (Item 9) to select the connection type you wish to use. When using either the balanced or unbalanced input, make sure that no cables or equipment are connected to the unused input, as this may degrade operation. The unused input does not require to be terminated and this should not be done.

9Input 1 Balanced/Unbalanced switch

Use to select the connection type for Input 1.

10Inputs 1-7

These inputs are suitable for any 'line level' source equipment such as CD players, DAB or FM/AM tuners etc.

Note: These inputs are for analog audio signals only. They should not be connected to the digital output of a CD player or any other digital device.

11Tape/Rec In/Out

Connect to a tape deck or to the analog output sockets on a MiniDisc, portable digital music player or CD recorder using an interconnect cable from the recorder's Line Out sockets to the amplifier's Tape In sockets.

The Tape Input circuit of the 840A V2 is a "monitor" type, different from the other 7 inputs. For the 7 normal inputs, the source selected for listening to will be sent out of the Tape Out for recording. The source currently being listened to and (optionally) recorded is then shown on the front panel display.

However, when the Tape Input is selected a solid circle will appear beside TAPE MON indicating that the Tape Input is now being listened to with a different source being sent out of the Tape Out for recording. The recording source is also shown by a solid circle by the selected input and can be changed by pressing the other source buttons. To switch Tape Monitor off, simply press the Tape Mon input select button again, toggling this function off.

This feature is most useful when using 3-head analog cassette decks which allow the signal being recorded to be played back live off tape (via a 3rd head) whilst it is simultaneously recorded. It is then possible by toggling the Tape Monitor input on and off to compare directly in real time the original and recorded signal so that adjustments to the recording parameters of the tape machine can be made (consult the manual of your 3-head analog cassette deck for full details).

12Preamp Out

Connect these sockets to the inputs on an external power amplifier(s) or active subwoofers etc.

840A V2 specifications

The Cambridge Audio 840A V2 is a high-end integrated amplifier that stands out in the realm of audio equipment, delivering both exceptional sound quality and sophisticated design. This amplifier embodies the brand's philosophy of providing a genuine listening experience that captures the essence of music.

One of the key features of the 840A V2 is its Class XD amplification technology. This unique design combines the best aspects of Class A and Class AB amplification, allowing for low distortion while maintaining high efficiency. This ensures that the amplifier can deliver potent power to drive a wide range of speakers without compromising on audio fidelity. The Class XD design allows the amplifier to operate in Class A mode at low power levels, delivering warmth and detail, while switching to Class AB at higher power levels for greater efficiency and headroom.

The 840A V2 boasts a robust construction that not only enhances durability but also minimizes resonance and vibration, contributing to cleaner sound reproduction. With a meticulous attention to detail, the amplifier features a symmetrical layout, which aids in reducing unwanted noise and crosstalk. The use of premium components throughout the signal path ensures that the audio remains true to the source.

One of the most appealing aspects of the 840A V2 is its extensive connectivity options. It includes multiple RCA inputs, a dedicated phono stage for vinyl enthusiasts, and balanced XLR inputs, making it versatile enough to accommodate various audio sources. The headphone output is powered by a dedicated circuit, ensuring that headphone listening experiences are equally exquisite.

Additionally, the 840A V2 incorporates a high-quality remote control that allows users to conveniently adjust volume levels and switch between sources from a distance. The front panel features a clear display and intuitive controls which makes operating the amplifier straightforward, even for those who might be new to high-fidelity audio equipment.

In summary, the Cambridge Audio 840A V2 integrated amplifier is an exemplary piece of audio engineering. With its Class XD technology, premium build quality, versatile connectivity, and user-friendly design, it offers audiophiles and casual listeners alike the opportunity to experience their music in an immersive and dynamic way. Whether paired with high-end speakers or used in a modest setup, the 840A V2 delivers a performance that reflects Cambridge Audio’s commitment to sound excellence.