Quick Start
1.Install the Express 10/100 Stackable Hub in a rack or on a shelf or table, plug it in, and turn the power on.
Intel Express
10/100 Stackable Hub
Change hub speed
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Collision | Power | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Managed |
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Status |
|
|
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 16 | 17 | 18 | 19 | 20 | 21 | 22 | 23 | 24 | Green (left) |
Link = solid | ||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Activity = blink |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Amber (right) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Wrong speed = blink |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Disabled = solid |
Rack: Use the four small screws to attach the brackets to the hub. Use the four large screws (not shown) to attach the hub to the rack.
Shelf: Attach the four rubber feet to the bottom before placing on a shelf or table.
2. Connect either
The default hub speed is 100 Mbps. Press
Change Hub Speed to operate at 10 Mbps.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Intel Express |
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 10/100 Stackable Hub |
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Change hub speed |
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Collision | Power | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Managed |
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Status |
|
|
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 16 | 17 | 18 | 19 | 20 | 21 | 22 | 23 | 24 | Green (left) |
Link = solid | ||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Activity = blink |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Amber (right) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Wrong speed = blink |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Disabled = solid |
All ports operate at the same speed
Use Category 5 (CAT 5)
For this connection | Use this cable |
Hub to server or workstation | |
Hub to print server | |
Hub to switch | Crossover TPE |
Hub to hub (10 Mbps only) | Crossover TPE |
3. Check the LEDs for links. You’re done.
On solid indicates a valid |
|
|
|
|
|
|
|
link (may take up to 6 |
|
|
|
|
|
| Amber LED |
seconds). Blinking | Green LED |
|
|
|
|
| |
|
|
|
|
| |||
indicates activity on the | (left side) |
|
|
|
|
| (right side) |
port. |
|
|
|
|
|
|
|
Cable distance can’t exceed 100 meters whether running at 10 or 100 Mbps.
Do not configure attached devices for full- duplex. Hubs aren’t capable of
Should normally be off. Blinking indicates a speed mismatch. For example, the hub is operating at 100 Mbps, but a 10 Mbps device is connected to the port. See pages
Next steps (Optional)
Continue to the next page if you want to connect multiple hubs.
1