Intel D510MO manual Clearing Passwords, Jumper Settings for the Bios Setup Program Modes

Page 42

Intel Desktop Board D510MO Product Guide

Figure 15 shows the location of the Desktop Board’s BIOS configuration jumper block.

Table 15. Jumper Settings for the BIOS Setup Program Modes

Jumper

 

 

Setting

Mode

Description

 

 

 

 

Normal (default) (1-2)

The BIOS uses the current configuration and

 

 

passwords for booting.

 

 

 

 

Configure (2-3)

After the Power-On Self-Test (POST) runs, the

 

 

BIOS displays the Maintenance Menu. Use this

 

 

menu to clear passwords.

 

 

 

 

Recovery (None)

The BIOS recovers data from a recovery diskette

 

 

in the event of a failed BIOS update.

 

 

 

Clearing Passwords

This procedure assumes that the board is installed in the computer and the configuration jumper is set to normal mode.

1.Observe the precautions in "Before You Begin" on page 23.

2.Turn off all peripheral devices connected to the computer. Turn off the computer. Disconnect the computer’s power cord from the AC power source (wall outlet or power adapter).

3.Remove the computer cover.

4.Find the configuration jumper block (see Figure 15, B).

5.Place the jumper on pins 2-3 as shown below.

6.Replace the cover, plug in the computer, turn on the computer, and allow it to boot.

7.The computer starts the Setup program. Setup displays the Maintenance menu.

8.Use the arrow keys to select Clear Passwords. Press <Enter> and Setup displays a pop-up screen requesting that you confirm clearing the password. Select Yes and press <Enter>. Setup displays the maintenance menu again.

9.Press <F10> to save the current values and exit Setup.

42

Image 42
Contents Intel Desktop Board D510MO Product Guide FCC Declaration of Conformity Revision HistoryRevision Revision History Date Canadian Department of Communications Compliance StatementIntended Uses PrefaceIntended Audience Document OrganizationTerminology Intel Desktop Board D510MO Product GuideTerm Description Contents Board Status and Error Messages Contents TablesViii Desktop Board Features Feature SummaryInstantly Available PC TechnologyTo find information Visit this World Wide Web site About… Desktop Board Features Desktop Board ComponentsLabel Description Processor System MemoryIntegrated Graphics Subsystem Intel NM10 Express Chipset Operating System SupportOnboard Audio Subsystem Audio Jack Support Item DescriptionLegacy Input/Output I/O Controller LAN SubsystemExpandability USB 2.0 SupportSata Interface LED Color LED State IndicatesPCI/PCI Express Auto Configuration Security PasswordsPower Management Features Hardware SupportInstantly Available PC Technology LAN Wake Capabilities Real-Time Clock BatteryEnergy STAR*, e-Standby, and ErP Compliance Energy Star RequirementsInstalling and Replacing Desktop Board Components Before You BeginIntel Desktop Board D510MO Product Guide Observe Safety and Regulatory Requirements Installation PrecautionsPrevent Power Supply Overload Installing and Replacing Desktop Board ComponentsInstalling the I/O Shield Installing the I/O ShieldInstalling and Removing the Desktop Board Installing and Removing MemoryInstalling DIMMs Use DDR2 DIMMsInstalling a Dimm Connecting Sata Drives Removing DIMMsConnecting the Serial ATA Cable Installing a Wireless LAN Card Installing and Replacing Desktop Board Components Connecting to the Internal Headers Internal HeadersPin Signal Name Ground Connecting the Front Panel Audio HeaderPin Signal Name Front Panel Audio Header for Intel HD AudioConnecting to the S/PDIF Header Connecting to the Serial HeadersConnecting to the Parallel Port Header Connecting to the Front Panel Wireless Activity LED Header Front Panel Wireless Activity LED HeaderFront Panel Header Signal Names Connecting to the Front Panel HeaderConnecting to the Front Panel USB 2.0 Headers Front Panel USB HeaderConnecting a Chassis Fan Location of the Chassis Fan HeaderConnecting the Power Supply Cable Connecting a Power Supply CableSetting the Bios Configuration Jumper Bios Configuration Jumper BlockClearing Passwords Jumper Settings for the Bios Setup Program ModesJumper Setting Mode Description Replacing the Battery PrécautionΠροσοχή Vigyázat Oсторога Removing the Battery Intel Desktop Board D510MO Product Guide Updating the Bios Updating the Bios with the Intel Express Bios Update UtilityUpdating the Bios with the Iflash Memory Update Utility Obtaining the Bios Update FileUsing the Iflash Memory Update Utility Updating the Bios Recovering the BiosAcceptable Drives/Media Types for Bios Recovery Media Type Can be Used for Bios Recovery?Intel Desktop Board D510MO Product Guide Bios Beep Codes Board Status and Error MessagesBios Beep Codes Type Pattern FrequencyBios Front-panel Power LED Blink Codes Bios Front-panel Power LED Blink CodesPost Error Messages Post Error MessagesSafety Standards Safety StandardsPlace Battery Marking Regulatory ComplianceEuropean Union Declaration of Conformity Statement Product Ecology Statements Recycling ConsiderationsRegulatory Compliance Français DeutschEspañol MalayPortuguese RussianTürkçe Lead-free 2LI/Pb-free 2LI Board Lead-Free Second Level Interconnect MarksDescription Mark Restriction of Hazardous Substances RoHS China RoHS Environmentally Friendly Use Period MarkIntel Desktop Board D510MO Product Guide EMC Regulations EMC RegulationsRegulation Class B Title Ensure Electromagnetic Compatibility EMC Compliance Product Certifications Board-Level Certification MarkingsProduct Certification Markings Chassis and Component Certifications Europe