Lenovo TC S51-8172, TC A51-8425, TC A51-8424, TC A51-8428, TC S51-8171 manual To connect To disconnect

Page 11

vConnect all power cords to a properly wired and grounded electrical outlet.

vConnect to properly wired outlets any equipment that will be attached to this product.

vWhen possible, use one hand only to connect or disconnect signal cables.

vNever turn on any equipment when there is evidence of fire, water, or structural damage.

vDisconnect the attached power cords, telecommunications systems, networks, and modems before you open the device covers, unless instructed otherwise in the installation and configuration procedures.

vConnect and disconnect cables as described in the following table when installing, moving, or opening covers on this product or attached devices.

To connect:

To disconnect:

1.

Turn everything OFF.

1.

Turn everything OFF.

2.

First, attach all cables to devices.

2.

First, remove power cords from outlet.

3.

Attach signal cables to connectors.

3.

Remove signal cables from connectors.

4.

Attach power cords to outlet.

4.

Remove all cables from devices.

5.

Turn device ON.

 

 

 

 

 

 

DANGER

Le courant électrique provenant de l’alimentation, du téléphone et des câbles de transmission peut présenter un danger.

Pour éviter tout risque de choc électrique :

vNe manipulez aucun câble et n’effectuez aucune opération d’installation, d’entretien ou de reconfiguration de ce produit au cours d’un orage.

vBranchez tous les cordons d’alimentation sur un socle de prise de courant correctement câblé et mis à la terre.

vBranchez sur des socles de prise de courant correctement câblés tout équipement connecté à ce produit.

vLorsque cela est possible, n’utilisez qu’une seule main pour connecter ou déconnecter les câbles d’interface.;

vNe mettez jamais un équipement sous tension en cas d’incendie ou d’inondation, ou en présence de dommages matériels.

vAvant de retirer les carters de l’unité, mettez celle-ci hors tension et déconnectez ses cordons d’alimentation, ainsi que les câbles qui la relient aux réseaux, aux systèmes de té lécommunication et aux modems (sauf instruction contraire mentionnée dans les procédures d’installation et de configuration).

vLorsque vous installez, que vous déplacez, ou que vous manipulez le présent produit ou des périphériques qui lui sont raccordés, reportez-vous aux instructions ci-dessous pour connecter et déconnecter les différents cordons.

Important safety information

ix

Image 11
Contents User Guide Types 8424, 8425 Types 8171, 8172 Page User Guide Types 8424, 8425 Types 8171, 8172 Page Contents Iv User Guide Conditions that require immediate action Important safety informationPower cords and power adapters General safety guidelinesService Batteries Extension cords and related devicesPlugs and outlets Heat and product ventilation CD and DVD drive safetyAdditional safety information To connect To disconnect Connexion Déconnexion Lithium battery noticeModem safety information Consignes de sécurité relatives au modem Laser compliance statementXii User Guide Information resources OverviewFeatures Expansion Input/output featuresPower Security featuresIBM preinstalled software Available options Operating systems preinstalled varies by modelSpecifications Supported operating positions User Guide Handling static-sensitive devices Installing optionsInstalling external options Cover keylock some models Obtaining device drivers Locating connectors on the rear of your computerOpening the cover Locating components Accessing system board components and drives Identifying parts on the system board Installing memory Installing PCI adapters What to do next Removing and replacing the batteryRemoving and replacing an optical drive Removing and replacing a diskette drive Installing security featuresIntegrated security cable Identifying security locksUser Guide Cover lock Password protectionTo install a rope clip Rope clipClosing the cover and connecting the cables Erasing a lost or forgotten password clearing CmosExiting from the IBM Setup Utility program Using the IBM Setup UtilityStarting the IBM Setup Utility program Viewing and changing settingsIDE Drive User Password Password considerationsUser Password Administrator PasswordSelect Security Profile by Device IDE Drive Master PasswordSetting, changing, and deleting a password Using Security Profile by DeviceChanging the startup device sequence Advanced settingsSelecting a startup device Selecting a temporary startup deviceUpdating flashing Bios from your operating system Appendix A. Updating POST/BIOSUpdating flashing Bios from a diskette Recovering from a POST/BIOS update failure Cleaning a mouse with a ball Appendix B. Cleaning the mouseCleaning an optical mouse User Guide Basic AT commands Appendix C. Manual modem commandsInternal speaker on until carrier detected Low speaker volumeSet Pulse dial as default Set Tone Dial as defaultExtended AT commands MNP/V.42/V.42bis/V.44 commands Fax Class 2 commands Fax Class 1 commandsVoice commands Appendix C. Manual modem commands User Guide Appendix D. Notices IBM TrademarksIndex Special characters Page Page Part Number 19R0474