Sanyo XP51L SETTING-UP Projector, Connecting AC Power Cord, For Continental Europe For the U.K

Page 8

PREPARATION

SETTING-UP PROJECTOR

CONNECTING AC POWER CORD

This projector uses nominal input voltages of 100-120 V or 200-240 V AC. This projector automatically selects correct input voltage. It is designed to work with single-phase power systems having a grounded neutral conductor. To reduce risk of electrical shock, do not plug into any other type of power system.

Consult your authorized dealer or service station if you are not sure of type of power supply being in use.

Connect a projector with a peripheral equipment before turning a projector on. (Refer to pages 12 ~ 14 for connection.)

CAUTION

For safety, unplug AC Power Cord when an appliance is not used.

When this projector is connected to outlet with AC Power Cord, an appliance is in Stand-by Mode and consumes a little electric power.

Connect AC Power Cord (supplied) to a projector. AC outlet must be near this equipment and must be easily accessible.

NOTE ON POWER CORD

AC Power Cord must meet requirement of country where you use a projector.

Confirm an AC plug type with chart below and proper AC Power Cord must be used.

If supplied AC Power Cord does not match your AC outlet, contact your sales dealer.

Projector side						AC Outlet side


		For the U.S.A. and Canada				For Continental Europe		For the U.K.


			Ground

To POWER CORD CONNECTOR on your projector.

To the AC Outlet.

(120 V AC)

To the AC Outlet.

(200 - 240 V AC)

To the AC Outlet.

(200 - 240 V AC)

8

Image 8

Contents Model PLC-XP50/XP51 To the Owner Safety Instructions Voor de klanten in NederlandCompliances Plummer Street, Chatsworth, CaliforniaTable of Contents Features and Design Compact Design Digital Zoom for ComputerHOT AIR Exhausted PreparationName of Each Part of Projector For Continental Europe For the U.K SETTING-UP ProjectorConnecting AC Power Cord Preparation Positioning Projector Room LightPreparation Adjustable Feet Installing Projector in Proper PositionPreparation Moving Projector Connecting Projector Terminals of ProjectorConnect computer output Digital DVI-D type to this terminal Refer to P13A Projector Connecting to ComputerTerminals Connecting to Video Equipment Operation of Remote Control Inside the Battery Compartment BOXBefore Operation Laser Pointer FunctionRemove battery Compartment lidSlide batteries into CompartmentTOP Controls and Indicators Flow of ON-SCREEN Menu Operation HOW to Operate ON-SCREEN MenuOperating ON-SCREEN Menu Press Menu Button while connecting to PC input source Used to adjust picture imageBefore Operation Menu BAR Used to selectBasic Operation Turning on / OFF ProjectorTurning on Projector Turning OFF ProjectorAdjusting Screen Keystone AdjustmentFocus adjustment may not function properly if the image is Corrected by Keystone adjustmentSound Adjustment Computer Input Selecting Input SourceSelecting Computer System Rgbav HdcpPC System Menu Automatic MULTI-SCAN SystemAuto PC Adjustment Auto PC AdjustmentPC Adjust Menu Auto PC AdjComputer Input Manual PC Adjustment Full screen Display areaDisplay area H Picture Image Select Image Level Select DirectImage Level Select Menu Image Select MenuPicture Screen Adjustment Screen MenuWhen video input signal is connected to Video jack Video InputVideo Select VideoSelecting Video System AutoAV System Menu Video or S-VIDEO AV System Menu Component VideoPicture level adjusted for picture with fine tone CinemaProvides image at a normal video aspect ratio of 4 Provides image at a wide screen ratio of 16Picture Image Picture Image AdjustmentsImage Adjust Menu List Mode Picture ImageColor temp White balance RedWhite balance Green White balance BlueSetting Menu SettingSetting Menu Anamorphic Blue backDisplay Menu positionTo change the code of the Remote Control Unit Power managementRemote control To change the code of ProjectorWireless Mouse mode Projector modeLamp counter reset Factory defaultOperating Wireless Mouse InstallationOperating Wireless Mouse AppendixStation MaintenanceIndicatorIndicator Appendix AIR Filter Care and Cleaning Cleaning Projection LensRecommendation Pull up and removeLamp Replacement Lamp ReplacePOA-LMP67for PLC-XP50/XP50L POA-LMP81for PLC-XP51/XP51LMessage Lamp replace counter reset? is displayed. Move Reset Lamp Replace CounterAppendix Lamp Replace Counter Pointer to Yes and then press Select buttonTroubleshooting Service Appendix Indicators and Projector Condition Appendix Compatible Computer Specifications ResolutionMenu Tree PC sourceSystem Setting Sound Technical Specifications Appendix Configurations of Terminals Control Port ConnectorUSB Connector Series B Computer INPUT-1 and Monitor OUT Terminals AnalogLens Replacement Appendix Optional PartsAppendix Part No 315 6910 1AA6P1P3972A- MH5A