Sanyo PLC-XP50L To change the code of Projector, To change the code of the Remote Control Unit

Page 39

SETTING

Power management

This projector is equipped with a power management function. When the input signal is interrupted and any button is not pressed for 30 seconds or more, the power management function operates in order to reduce power consumption and conserve lamp operating time. The factory default settings for power management are "Ready" and "5 Min".

OPERATION

1)If the input signal is interrupted and any button is not pressed for 30 seconds or more, the message "No signal" and the timer display appears on the screen. Then the count-down starts for the time being set.

If "Ready" is selected

2)When the set time is elapsed, the lamp will be switched off and lamp cooling starts. The READY indicator will be switched off while the lamp cooling is in progress, and the projector cannot be operated during this time.

3)When the lamp cooling is completed, the READY indicator starts flashing to notify the operator that power management mode is active. In this condition, the lamp will turn on and images will be projected if a signal starts being input or the projector is operated.

If "Shut down" is selected

2)When the set time is elapsed, the lamp will be switched off and lamp cooling starts. The READY indicator will be switched off while the lamp cooling is in progress, and the projector cannot be operated during this time.

3)When the lamp cooling is completed, the power switches off.

If "Off" is selected

The power management function is canceled.

When a SELECT button is pressed, the adjustment screen is displayed.

Use the POINT LEFT/RIGHT button(s) to select the power management function mode ("Off", "Ready" or "Shut down").

Use the POINT DOWN button to move the pointer to the time setting, and then use the POINT LEFT/RIGHT button(s) to set the time (1 minute to 30 minutes).

On start

Time left until Lamp off.

When this function is “On,” projector is automatically turned on just by connecting AC Power cord to a wall outlet.

Note ; Be sure to turn projector off properly (refer to section “TURNING OFF PROJECTOR” on P20). If projector is turned off in wrong steps, On Start function does not operate properly.

Remote control

This projector has eight different remote control codes; the factory- set normal code (Code 1) and the other seven codes (Code 2 to Code 8). This switching function prevents remote control operation mixture (jam) when operating several projectors or video equipment together.

For example operating projector in “Code 7,” both projector and Remote Control Unit must be switched to “Code 7.”

To change the code of Projector;

To change the Remote control code of the projector used in ON-

SCREEN MENU is selectable from Code 1 to Code 8.

To change the code of the Remote Control Unit;

To change the remote control code of the Remote Control Unit, set the DIP switches 1-3 inside the battery compartment box of the Remote Control Unit. (Refer to P15.)

When pressing SELECT button at Remote control, Remote control code Menu appears.

39

Image 39
Contents Model PLC-XP50/XP51 To the Owner Voor de klanten in Nederland Safety InstructionsPlummer Street, Chatsworth, California CompliancesTable of Contents Compact Design Digital Zoom for Computer Features and DesignPreparation Name of Each Part of ProjectorHOT AIR Exhausted SETTING-UP Projector Connecting AC Power CordFor Continental Europe For the U.K Room Light Preparation Positioning ProjectorInstalling Projector in Proper Position Preparation Adjustable FeetPreparation Moving Projector Refer to P13 Connecting ProjectorTerminals of Projector Connect computer output Digital DVI-D type to this terminalConnecting to Computer TerminalsA Projector Connecting to Video Equipment Laser Pointer Function Operation of Remote ControlInside the Battery Compartment BOX Before OperationCompartment Remove batteryCompartment lid Slide batteries intoTOP Controls and Indicators HOW to Operate ON-SCREEN Menu Operating ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Used to select Press Menu Button while connecting to PC input sourceUsed to adjust picture image Before Operation Menu BARTurning OFF Projector Basic OperationTurning on / OFF Projector Turning on ProjectorCorrected by Keystone adjustment Adjusting ScreenKeystone Adjustment Focus adjustment may not function properly if the image isSound Adjustment Rgbav Hdcp Computer InputSelecting Input Source Selecting Computer SystemAutomatic MULTI-SCAN System AutoPC System Menu Auto PC Adj PC AdjustmentAuto PC Adjustment PC Adjust MenuComputer Input Manual PC Adjustment Display area Display area HFull screen Image Select Menu Picture Image SelectImage Level Select Direct Image Level Select MenuScreen Menu Picture Screen AdjustmentSelect Video When video input signal is connected to Video jackVideo Input VideoAV System Menu Component Video Selecting Video SystemAuto AV System Menu Video or S-VIDEOCinema Picture level adjusted for picture with fine toneProvides image at a wide screen ratio of 16 Provides image at a normal video aspect ratio of 4Picture Image Adjustments Image Adjust MenuPicture Image Picture Image List ModeWhite balance Blue Color tempWhite balance Red White balance GreenSetting Setting MenuSetting Menu Menu position AnamorphicBlue back DisplayTo change the code of Projector To change the code of the Remote Control UnitPower management Remote controlFactory default Wireless Mouse modeProjector mode Lamp counter resetAppendix Operating Wireless MouseInstallation Operating Wireless MouseMaintenance IndicatorIndicatorStation Pull up and remove Appendix AIR Filter Care and CleaningCleaning Projection Lens RecommendationPOA-LMP81for PLC-XP51/XP51L Lamp ReplacementLamp Replace POA-LMP67for PLC-XP50/XP50LPointer to Yes and then press Select button Message Lamp replace counter reset? is displayed. MoveReset Lamp Replace Counter Appendix Lamp Replace CounterTroubleshooting Service Appendix Indicators and Projector Condition Resolution Appendix Compatible Computer SpecificationsPC source Menu TreeSystem Setting Sound Technical Specifications Computer INPUT-1 and Monitor OUT Terminals Analog Appendix Configurations of TerminalsControl Port Connector USB Connector Series BAppendix Optional Parts Lens ReplacementAppendix Part No 315 6910 1AA6P1P3972A- MH5A