Sanyo PLC-XP100BKL, PLC-XP100L owner manual Appendix, Troubleshooting

Page 64

Appendix

Troubleshooting

Before calling your dealer or service center for assistance, check the items below once again.

1.Make sure you have properly connected the projector to peripheral equipment as described on pages 20–21.

2.Check the cable connection. Make sure that all computers, video equipment, and power cords are properly connected.

3.Make sure that all power is switched on.

4.If the projector still does not produce an image, restart your computer.

5.If an image still does not appear, disconnect the projector from your computer and check your computer monitor’s display. A problem may be noticed with your graphics controller rather than with the projector. (When you reconnect the projector, be sure to turn the computer and monitor off before you turn on the projector. Turn on equipment in the order of the projector and computer.)

6.If a problem still persists, check the following solutions.

 

 

Problem:

Try These Solutions

 

 

No power..

● Plug the power cord of the projector into the AC outlet.

 

 

 

 

 

● Wait until the POWER indicator stops blinking to turn on the projector again. (See page

 

 

 

 

 

23)

 

 

 

 

 

● Check the WARNING TEMP. indicator. If the WARNING TEMP. indicator is blinking, the

 

 

 

 

 

projector cannot be turned on. (See page 63.)

 

 

 

 

 

● Check the projection lamp. (See page 59.)

 

 

 

 

 

● Unlock the Key lock function for the projector. (See page 53)

 

 

 

 

 

● See if the filter cartridge is inserted. (See page 57)

 

 

 

 

 

 

 

 

Image is out of focus..

● Adjust the focus of the projector.

 

 

 

 

 

● Make sure the projection screen is at least 4.6’ (1.4 m) away from the projector.

 

 

 

 

 

● Check the projection lens to see if it needs cleaning.

 

 

 

 

 

NOTE: Moving the projector from a cool to a warm place may result in moisture

 

 

 

 

 

condensation on the projection lens. If this happens, leave the projector off and

 

 

 

 

 

wait until condensation evaporates.

 

 

Picture is left/right

● Check the Ceiling/Rear function. (See pages 40, 44)

 

 

reversed..

 

 

 

Picture is top/bottom

● Check the Ceiling function. (See pages 40, 44.)

 

 

reversed..

 

 

 

Some displays are

● Check the Display function. (See page 48.)

 

 

not seen during

 

 

 

operations..

 

 

 

 

 

 

 

 

 

No image..

● Check the connection between your computer or video equipment and the projector.

 

 

 

 

 

● It takes about 30 seconds to display an image after turning on the projector.

 

 

 

 

 

● See if the selected system is corresponding with your computer or video equipment.

 

 

 

 

 

● Make sure the temperature is not out of specified operating temperature (41˚F–104˚F

 

 

 

 

 

[5˚C–40˚C]).

 

 

 

 

 

● The end of lamp life is approaching. Replace the lamp with a new one promptly. (See

 

 

 

 

 

 

 

 

 

 

page 59)

 

 

 

 

 

 

 

 

appears on the

 

 

 

screen

 

 

 

 

 

 

● The filter is out of scroll. Replace the filter cartridge with a new one promptly. (See pages

 

 

 

 

 

56-57)

 

 

appears on the

 

 

 

screen

 

 

 

 

 

 

 

 

64

Page 63 Page 65
Image 64
Page 63 Page 65
Contents Model PLC-XP100L PLC-XP100BKL Features and Design Table of Contents To The Owner Risk of Electric Shock Do not OpenSafety Instructions Voor de klanten in NederlandAir Circulation Top PanelInstalling the Projector in Proper Directions Positioning PrecautionsMoving the Projector Transporting the ProjectorCompliance Federal Communications Commission NoticePart Names and Functions BottomRear Terminal Side Control and Indicators Remote Control 4P-TIMER button @0FOCUS buttons Adjust the focus p.28 @1NO Show button3MENU button 5D..ZOOM buttonRemote Control Receivers and Operating Range Remote Control Battery InstallationWired Remote Control Transmitter Remote Control Code Installation Adjustable FeetLens Installation Removing the lensAttaching the lens to the projector Connecting to a Computer Digital and Analog RGB USB R H/V Digital Analog Monitor OUT Control PortConnecting to Video Equipment Video, S-Video Monitor Out Signal TableFor the U..K Connecting the AC Power CordFor the U..S..A.. and Canada For Continental Europe What is PIN code? Basic OperationTurning On the Projector Enter a PIN codeTurning Off the Projector How to Operate the On-Screen Menu Menu Bar Operating with Projector Control Lens button Point buttonsOperating with Remote Control Timer button Filter buttonNo Show button Mouse Pointer buttonWireless Mouse Operation Pointer FunctionPointer Mouse Pointer buttonRemote Control Operation Input SelectionInput Side Control OperationComputer Input Source Selection Menu OperationInput Menu Source Select MenuVideo Input Source Selection Video Pb/Cb, Pr/CrComputer Input Computer System SelectionAutomatic Multi-Scan System Selecting Computer System ManuallyAuto PC Adjustment PC Adjust MenuDirect Operation Auto PC adjManual PC Adjustment Reset Mode freeTo store the adjusted data StoreImage Level Selection StandardReal ImageScreen Size Adjustment Screen MenuKeystone CeilingRear Digital zoom +Video Input Video System SelectionCinema Provide the image at the normal video aspect ratio Keystone Image Adjustment Image Adjust MenuPointer Mode Picture ImageColor M MenuColor Palette DELWhite balance Red/Green/Blue Offset Red/Green/BlueSharpness GammaSetting SettingLogo select LogoLogo Capture Enter a Logo PIN code Change the Logo PIN code lock settingChange the Logo PIN code RC sensor Wireless Mouse mode Projector modePower management USBSecurity Key lock PIN code lockSecurity Key lock PIN code lockChange the PIN Code Lock setting Change the PIN code lock settingChange the PIN Code Enter a PIN codeFilter counter Factory defaultTest pattern Maintenance and Care Filter InstructionsMaintenance and Care Filter counter Lamp Replace indicator Lamp ReplacementReset the Lamp counter p.60 Replacement Lamp Type No Resetting the Lamp CounterModel No.. of your projector Lamp Handling Precautions Cleaning the Projection Lens Cleaning the Projector CabinetLamp indicator lights on and other four indicators blink Then check the matters belowTroubleshooting AppendixRemote control does Wireless mouseNot work Function does notImage Adjust Menu TreeComputer Input/Video Input InformationPC Adjust System Image SelectScreen SystemSetting USBIndicators and Projector Condition Projector ConditionAppendix Indicators Compatible Computer Specifications Resolution59.940 Panel Resolution Signal CompatibilityPower Remote ControlLens Replacement To the sales and service engineersOptional Parts PJ Link NoticeControl Port Connector D-sub 9 pin Configurations of TerminalsANALOG/ Monitor OUT Mini D-sub 15 pin PIN Code Lock No PIN Code Number MemoLogo PIN Code Lock No Dimensions Operation ExampleFunctional Execution Command FormatStatus Read Command CR0KC3AL-a
Related manuals
Manual 1 pages 9.69 Kb

PLC-XP100BKL, PLC-XP100L specifications

The Sanyo PLC-XP100L is a high-performance LCD projector designed to meet the needs of both corporate environments and educational institutions. Renowned for its reliability and impressive image quality, the PLC-XP100L incorporates several advanced technologies that make it a strong contender in the projector market.

One of the standout features of the PLC-XP100L is its exceptional brightness. With a brilliant lumen output, this projector delivers clear and vibrant images, even in well-lit rooms. The high brightness level ensures that presentations and videos remain visible without straining the eyes, making it ideal for use in large conference rooms or lecture halls. The projector's contrast ratio further enhances image quality, providing deeper blacks and brighter whites for a well-balanced picture.

The resolution capabilities of the Sanyo PLC-XP100L also contribute to its appeal. Supporting native XGA resolution (1024 x 768), it ensures that text, images, and graphics are rendered sharply and clearly. This makes it suitable for displaying detailed spreadsheets, intricate designs, or high-definition video content. Additionally, it includes technology that allows for scaling to accommodate various input formats, enabling versatility in multimedia presentations.

Portability is another significant characteristic of the PLC-XP100L. Despite its powerful performance, the projector is relatively lightweight, allowing for easy transportation between different locations. Users can seamlessly move it for various applications, whether for business meetings, classroom teaching, or community events.

Connectivity is another area where the Sanyo PLC-XP100L excels. With multiple input options, including VGA, composite video, and S-video, it can seamlessly connect to various devices, such as laptops, DVD players, and even digital cameras. This flexibility allows users to create a dynamic and engaging presentation experience without being limited by compatibility issues.

Furthermore, the PLC-XP100L features long-life lamp technology, which extends the lifespan of the projector lamp significantly. This not only reduces operational costs but also minimizes the hassle of frequent replacements, making it a cost-effective choice for organizations.

In summary, the Sanyo PLC-XP100L is a robust LCD projector that combines impressive brightness, high resolution, and exceptional portability with versatile connectivity options. Its features and technologies make it a reliable choice for professionals and educators looking to make impactful presentations.
Top Page Image Contents