Hitachi CP-S840W/E Adjustments and functions, Memory function, To return to the initial setting

Page 16

Adjustments and functions

	STANDBY/ON	MUTE
	FREEZE
STANDBY/ON
	MAGNIFY VOLUME
	INPUT
MUTE	OFF
MUTE
	POSITION ON	LASER
	MENU

	RESET	2, 3
	RESET
			RESET	RIGHT
	1, 2, 3	1	MENU ON	MOUSE ON
	1, 2, 3	1	BLANK	TIMER
			RGB	VIDEO
				INPUT
1 Press the MENU (	) buttons or the MENU ON /

OFF button.

∙On-screen menus are displayed on the screen.

2 Select the menu to be adjusted using the MENU (	)
buttons or DISK PAD.

∙Menu displayed in green is selected.

3 Select the item to be adjusted using the MENU (	)
buttons or DISK PAD.

∙Item displayed in green can be adjusted.

When no operation is done for about 5 ~ 10 seconds, menu screen will go off.

Memory function

Individual memory functions are provided for the VIDEO, RGB1 and RGB2 input terminals. Adjustments are saved after power off.

To return to the initial setting

∙Resetting menu items (SETUP, INPUT, IMAGE, OPT.)

(1)Select the menu item to return to the initial setting.

(2)Press the RESET button.

(3)Select the DEFAULT (To select the CANCEL is not changed). (Display shown on the right will appear.)

∙Resetting adjustment items (VOLUME, BRIGHT etc.)

(1)Select the adjustment item to return to the initial setting.

(2)Press the RESET button.

SETUP INPUT IMAGE OPT .

	VOLUME	RESET		'SETUP'
	BRIGHT
	CONTRAST		DEFAULT
	SHARPNESS		DEFAULT
	SHARPNESS		CANCEL
	COLOR		CANCEL
	COLOR
	TINT
	COLOR BAL R			B

16

Image 16

Contents Features ContentsOutline Operating GuideFor the Customers in U.K Video signal cables Power cordBefore use Instructions to UsersDo not look directly at the lens when Lamp is lit Do not install this unit in an unstable placeDo not use power supplies other Than that specified If any abnormality occursBe careful in handling the power cord Do not stare directly into the laser apertureCleaning Handle the power cord carefullyUse of batteries When you are not going to use for a Clean inside the unit at least once two yearsWhen you are not going to use For a long time Do not place this unit where it gets hotVolume Cleaning the lensContents of shipping box Names and functions of each partRemote control sensor Main Power switch AC in socketVideo input terminal RGB input terminalRemote control transmitter How to insert batteries Names and functions of each partExample of the projector and screen installation InstallationHow to use foot adjusters Basic operations To project the pictureTo turn off the power PLUG&PLAYFreeze Function Magnifying FunctionTo return to the initial setting Adjustments and functionsMemory function SET UP How to use the SET UP menuBar display items VOLUME, Bright etc Numerical display items V POSIT, H Posit etcAUTO-adjustment AUTO-adjustment Confirm ScreenDuring AUTO-adjustment Adjustment Item Details of adjustmentReveal Connection to the video signal terminals Connection to the RGB signal terminalExample of computer signal Resolution Standard Display Dots KHz TypeComputer/signal Horizontal Timing µs Initial set signalsComputer/signal Vertical Timing lines Connection to the control signal terminal Control signal terminalADB Mac mouse PS/2 mouseSerial mouse Control command table Control command tableCommunication RS232C cable ReferenceCommand data Procedure of getting the Projector status Procedure of setting the Projector statusProcedure of default setting the Projector status Example of command errorExample of system setup Connecting various equipmentAC Inlet Computer Note type ComputerDesk typeCleaning the air filter Air filter Filter coverRemove the lamp cover How to replace lampLoosen two screws and pull the handle to remove Lamp Reset the lamp time Install the lamp cover and fix it using screwsLamp Indicator display Message tableOn-screen display ActionWhen you think something wrong RCA Jack terminal Input terminal Input/Output Dimension diagramOperating guide RGB cable