Hitachi CP-S840W/E Lamp, Install the lamp cover and fix it using screws, Reset the lamp time

Page 31

Lamp (continued)

4	Replace the lamp with new one and
	fix it using the same two screws.	Screw
	∙ Firmly tighten the lamp screws. Loose screws may cause
	bad connection of the connector which in turn may result	Lamp
	in malfunctioning.	Lamp
	in malfunctioning.
5	Install the lamp cover and fix it using screws.
5	∙ To prevent burn, install the lamp cover and secure it using the screws.

∙ Do not turn on the power with lamp cover removed.

Lamp cover

Screw

∙Whenever the lamp is replaced, reset the total operation time of the lamp. Do not reset if the lamp has not been replaced.

∙Do not perform resetting without changing the lamp, as this can cause lamp breakage.

2. Reset the lamp time

Please carry out the following operation within 10 minutes from power on, if you replaced the lamp after

2,000 hours.

MAGNIFY VOLUME

	OFF
	POSITION ON	LASER			STANDBY/ON
					STANDBY/ON
3					INPUT
3					MUTE
			1		MENU
2	RESET	RIGHT			3
2	MENU ON	MOUSE ON		1, 2	3
					RESET
	BLANK	TIMER
	RGB	VIDEO
	INPUT

ENGLISH

1)Press the RESET button on projector for 3 seconds or remote control TIMER button for 3 seconds and display the total lamp used time.

∙When accumulated operation time of the lamp reaches 1500 hours, the following display will appear at the bottom of the screen.

2)Press the RESET button on projector or remote control MENU ON button during displaying the lamp used time.

3)Select the “0” on the screen using the MENU ( ) button or DISK PAD.

LAMP 1500 h

LAMP 1500 □¬ 0 ■CANCEL

31

Image 31

Contents Operating Guide FeaturesContents OutlineFor the Customers in U.K Instructions to Users Video signal cablesPower cord Before useIf any abnormality occurs Do not look directly at the lens when Lamp is litDo not install this unit in an unstable place Do not use power supplies other Than that specifiedDo not stare directly into the laser aperture Be careful in handling the power cordClean inside the unit at least once two years CleaningHandle the power cord carefully Use of batteries When you are not going to use for aCleaning the lens When you are not going to use For a long timeDo not place this unit where it gets hot VolumeNames and functions of each part Contents of shipping boxRGB input terminal Remote control sensor Main Power switchAC in socket Video input terminalRemote control transmitter Names and functions of each part How to insert batteriesExample of the projector and screen installation InstallationHow to use foot adjusters To project the picture Basic operationsPLUG&PLAY To turn off the powerMagnifying Function Freeze FunctionTo return to the initial setting Adjustments and functionsMemory function Numerical display items V POSIT, H Posit etc SET UPHow to use the SET UP menu Bar display items VOLUME, Bright etcAdjustment Item Details of adjustment AUTO-adjustmentAUTO-adjustment Confirm Screen During AUTO-adjustmentReveal Connection to the RGB signal terminal Connection to the video signal terminalsResolution Standard Display Dots KHz Type Example of computer signalComputer/signal Horizontal Timing µs Initial set signalsComputer/signal Vertical Timing lines Control signal terminal Connection to the control signal terminalADB Mac mouse PS/2 mouseSerial mouse RS232C cable Reference Control command tableControl command table CommunicationCommand data Example of command error Procedure of getting the Projector statusProcedure of setting the Projector status Procedure of default setting the Projector statusComputerDesk type Example of system setupConnecting various equipment AC Inlet Computer Note typeAir filter Filter cover Cleaning the air filterRemove the lamp cover How to replace lampLoosen two screws and pull the handle to remove Lamp Reset the lamp time Install the lamp cover and fix it using screwsLamp Action Indicator displayMessage table On-screen displayWhen you think something wrong RCA Jack terminal Input terminal Input/Output Dimension diagramOperating guide RGB cable