Hitachi CPX328W user manual Replacing the lamp

Page 27

THE LAMP (continued)

Replacing the lamp

All projector lamps will wear out eventually. If used for long periods of time, the image could become darkened, and the color contrast could be impacted as well. We recommend that you replace your lamps early. If the LAMP indicator turns red, or a message prompts you to replace the lamp when you power up the projector, the lamp needs to be replaced. (See "Related Messages" (Vol.2 7 ) and "Regarding the Indicator Lamps" (Vol.2 8 ) for details.)

1

Turn off the projector, and unplug the

power cord. Allow the lamp bulb to cool

 

for at least 45 minutes, and prepare a

 

new lamp (sold separately: DT00511)

 

 

 

 

2

After making sure that the projector has

cooled adequately, slowly flip over the

projector, so that the bottom is facing up

5

Insert the new lamp, and tighten the 1

screw firmly to lock it in place

• Also steadily push the opposite side of the screwed side of the

lamp into the unit.

3 Unscrew the 2 screws, and remove the lamp cover

6

Replace the lamp cover, and tighten

the 2 screws firmly to lock it in

place

4

Unscrew the 1 screw, and slowly pull

out the lamp by the handle

• Be careful not to touch the inside of the lamp case.

7

Slowly turn the projector so that

the top is facing up

 

 

 

 

8

Turn on the projector power, and using

the menu, reset the lamp timer

• To reset the lamp timer, from the OPTION menu, select LAMP TIME.

ATTENTION • Make sure that the screws are screwed in firmly. Loose screws could result in damage or injury.

Do not use with lamp cover removed.

Do not reset the lamp timer without replacing the lamp. Reset the lamp timer always when replacing the lamp. The message functions will not operate properly if the lamp timer is not reset correctly.

When the lamp has been replaced after the message of "CHANGE THE LAMP ...THE POWER WILL TURN OFF AFTER 0 hr." is displayed, or the LAMP indicator is red, complete the following operation within 10 minutes of switching power ON.

NOTE The LAMP indicator is also red when the lamp unit reaches high temperature. Before replacing the lamp, switch power OFF, wait approximately 20 minutes, and switch power ON again. If the LAMP indicator is still red, replace the lamp.

26

Downloaded from www.Manualslib.com manuals search engine

Image 27
Contents CPS318W/CPX328W Manuale Distruzioni Vol.1 Informazioni di baseBrukerhåndbok Vol.1 Grunnleggende Contents Two AA batteries Projector FeaturesRemote control Projector With Lens CapConnect your devices to the projector Projector Part NamesRemote Control Adjusting the Projectors Elevator Feet Setting UP the ProjectorTop view Side view Adjusting the Screen Size and Projection DistanceConnecting Your Devices Function Projector Port Connection Cables Ports and CablesConnecting to a Computer Connecting Your DevicesConnecting to a VCR Connecting to a DVD PlayerConnecting to a Display Monitor Remove the battery Insert the batteries Cover Using the Remote ControlPutting batteries into the remote control unit Operating the remote controlTurning on the Power Selecting an Input Signal Turning OFF the Power Temporarily Muting the Sound Adjusting the VolumePress the Volume button Press Buttons to adjust VolumeAdjusting the Position Use Buttons to adjust PositionPress the Position button Press the Auto button Using the Automatic Adjustment FeatureAutomatic Adjustment for RGB Input Automatic Adjustment for Video InputPress the Keystone button Correcting Keystone DistortionsFreezing the Screen Using the Magnify FeatureSignal Searching Selecting the Aspect RatioTemporarily Blanking the Screen Press Buttons to adjust the level Using the Menu FunctionsSelect a menu using Buttons Then press Or Enter button Select an item using Buttons, then press Or Enter buttonOperating the PC Screen Available Functions Remote Control OperationLamp High Voltage High Temperature High PressureReplacing the lamp Caring for the air filter AIR FilterReplacing the air filter Caring for the lens Caring for the cabinet and remote control transmitterOther Care Caring for the inside of the projectorFor Technical see the end of this manual Multifunctional Settings Main MenuMain Menu PICTURE2 Menu Picture 1 MenuPicture 2 Menu PICTURE1 MenuVideo Input MenuInput Menu AutoStart UP Screen MenuScreen Menu BlankWhisper Option MenuOption Menu Auto OFFCheck the AIR Flow Related MessagesChange the Lamp No Input is DetectedPower Lamp Temp Regarding the Indicator LampsPhenomena That May Easily Be Mistaken for Machine Defects PhenomenonItems to be confirmed Specifications Dimension DiagramSpecification Warranty and AFTER-SERVICE Regulatory Notices Hitachi Atago Building