Hitachi CPX275W Installation of the Projector and Screen, Angle Adjustment, Side View

Page 6

INSTALLATION

Installation of the Projector and Screen

Refer to the drawing and table below for determining the screen size and projection distance.

ENGLISH

The projection distances shown in the table below are for full size (CP-S225W:800 x 600 dots / CP- X275W:1024 x 768 dots).

a: Distance from the projector to the screen. (±10%)

b: Distance from the lens center to the bottom of the screen. (±10%)

Table 1. Installation Reference

Screen size

 

a [inches (m)]

 

b

[inches (m)]

Min.

Max.

[inches (cm)]

 

 

 

 

 

 

 

 

40

(1.0)

37

(0.9)

46

(1.2)

3

(8.7)

 

 

 

 

 

 

 

 

60

(1.5)

57

(1.5)

69

(1.8)

5

(13.1)

 

 

 

 

 

 

 

 

80

(2.0)

77

(1.9)

93

(2.4)

7

(17.4)

 

 

 

 

 

 

 

 

100

(2.5)

96

(2.4)

116

(2.9)

9

(21.8)

 

 

 

 

 

 

 

 

120

(3.0)

116

(2.9)

139

(3.5)

10

(26.1)

 

 

 

 

 

 

 

 

150

(3.8)

145

(3.7)

174

(4.4)

13

(32.7)

 

 

 

 

 

 

 

 

200

(5.0)

194

(4.9)

233

(5.9)

17

(43.5)

 

 

 

 

 

 

 

 

Screen

TOP VIEW

Lens center

b

aSIDE VIEW

CAUTION • Install the projector in a suitable environment according to instructions of the accompanying manual “SAFETY INSTRUCTIONS” and this manual.

Please basically use liquid crystal projector at the horizontal position. If you use liquid crystal projector by the lens up position, the lens down position and the side up position, this may cause the heat inside to build up and cause damage. Be especially careful not to install it with ventilation holes blocked.

Do not install LCD projector in smoke effected environment. Smoke residue may buildup on critical parts (i.e.LCD panel, Lens Assy etc.).

Angle Adjustment

Use the foot adjusters on the bottom of the projector to adjust the projection angle. It is variable within 0˚ to 10˚ approximately.

1.Lift up the front side of the projector, and pressing the foot adjuster button, adjust the projection angle.

2.Release the button to lock at the desired angle.

3.Make the rear foot adjuster screw to adjust the left-right slope.

Foot Adjuster

Press the foot adjuster button Rear Foot Adjuster

CAUTION • Do not release the foot adjuster button unless the projector is being held; otherwise, the projector could overturn or fingers could get

caught and cause personal injury.

ENGLISH-5

Image 6
Contents CPX275W Contents Features Contents of packageBefore USE Front / Left View Before USEPart Names Rear / Right ViewFirst Loading Remote ControllerLoading the Batteries ReplacingAngle Adjustment InstallationInstallation of the Projector and Screen Installation ReferenceInstallation CablingCabling Power Connection Example of system setupPlug & Play Operations Power onPower OFF StandbyOperations Basic OperationBasic Operation Description Automatic Adjustment at Video Input Press the Auto button Set/Clear Mute Mode Press the Mute buttonAutomatic Adjustment at RGB Input Press the Auto button Menu Display Start/Stop Press the Menu buttonSelect Image Aspect Ratio Setup MenuSetup Menu Select Position of ImageInput Menu Input MenuImage Menu Setup Initial Screen Display Select Turn on withSelect Color Temperature Image Menu DescriptionSelect Menu Background Color Select with Options MenuOptions Menu Description Select Menu Display Language Select withSetup Initial Screen Display Select the Turn on with No Signal MenuNo Signal Menu Select Blank Screen Color Select the color withLamp MaintenanceLamp Lamp LifeMaintenance Resetting the Lamp TimerReplacing the Lamp Maintenance Inside the Equipment Air Filter MaintenanceOther Maintenance Cleaning the LensOSD Message TroubleshootingMessage Contents OSD MessagesIndicators Message TroubleshootingIndicators Message IndicatorSymptom SymptomSymptom Possible cause Remedy Specifications SpecificationsWarranty and AFTER-SERVICE Page Sub 15-pin Shrink Connector RGB Dimension DiagramSignal Connector Pin Assignment Mini Din 4-pin Connector S-VIDEOExample of computer signal TechnicalInitial set signals Connection to the Mouse Control RS-232C communication Communications settingCommand data ProtocolUsing the projector default settings Reset Command Requesting projector status Get commandChanging the projector settings Set command Increasing the projector setting value Increment commandCRC Be EF BA D2 Be EF FD D3 Be EF Ntsc PAL Regulatory Notices FCC Statement WarningFor the Customers in Canada Pour les utilisateurs au Canada Hitachi