Hitachi EDX-3270A, EDS3170A user manual Replacing the lamp

Page 27

THE LAMP (continued)

Replacing the lamp

All projector lamps will wear out eventually. If used for long periods of time, the image could become darkened, and the color contrast could be impacted as well. We recommend that you replace your lamps early. If the LAMP indicator turns red, or a message prompts you to replace the lamp when you power up the projector, the lamp needs to be replaced. (See "Related Messages" (Vol.2 7 ) and "Regarding the Indicator Lamps" (Vol.2 8 ) for details.)

1	Turn off the projector, and unplug the
1	power cord. Allow the lamp bulb to cool
	for at least 45 minutes, and prepare a
	new lamp (sold separately: DT00511 for
	ED-S3170A/DT00521 for ED-X3270A)


2	After making sure that the projector has
2	cooled adequately, slowly flip over the

projector, so that the bottom is facing up

5	Insert the new lamp, and tighten the 1
	screw firmly to lock it in place

• Also steadily push the opposite side of the screwed side of the

lamp into the unit.

3 Unscrew the 2 screws, and remove the lamp cover

6	Replace the lamp cover, and tighten
	the 2 screws firmly to lock it in

place

4	Unscrew the 1 screw, and slowly pull
	out the lamp by the handle

• Be careful not to touch the inside of the lamp case.

7	Slowly turn the projector so that
7	the top is facing up


8	Turn on the projector power, and using
8	the menu, reset the lamp timer

• To reset the lamp timer, from the OPTION menu, select LAMP TIME.

ATTENTION • Make sure that the screws are screwed in firmly. Loose screws could result in damage or injury.

•Do not use with lamp cover removed.

•Do not reset the lamp timer without replacing the lamp. Reset the lamp timer always when replacing the lamp. The message functions will not operate properly if the lamp timer is not reset correctly.

•When the lamp has been replaced after the message of "CHANGE THE LAMP ...THE POWER WILL TURN OFF AFTER 0 hr." is displayed, or the LAMP indicator is red, complete the following operation within 10 minutes of switching power ON.

NOTE • The LAMP indicator is also red when the lamp unit reaches high temperature. Before replacing the lamp, switch power OFF, wait approximately 20 minutes, and switch power ON again. If the LAMP indicator is still red, replace the lamp.

26

Image 27

Contents ED-S3170A / ED-X3270A Contents USB mouse Projector FeaturesSafety Instructions Remote controlOnly use the power cord that came with the projector Devices you will be using to the projectorPower cord Reference Part NamesFreeze button Keyboard buttons Auto button Blank button Volume button Mute buttonRGB button Search button STANDBY/ON button Video button 15 Aspect button Magnify buttonsAdjusting the Projectors Elevator Feet Setting UP the ProjectorAdjusting the Screen Size and Projection Distance ScreenTop view Side view Connecting Your Devices Function Projector Port Connection Cables Ports and CablesConnecting to a Computer Connecting Your DevicesConnecting to a VCR Connecting to a DVD PlayerConnecting to a Display Monitor Using the Remote Control Putting batteries into the remote control unitOperating the remote control Turning on the Power Selecting an Input Signal Turning OFF the Power Temporarily Muting the Sound Adjusting the VolumePress the Volume button Press Buttons to adjust VolumeAdjusting the Position Use Buttons to adjust PositionPress the Position button Press the Auto button Using the Automatic Adjustment FeatureAutomatic Adjustment for RGB Input Automatic Adjustment for Video InputOn the screen to aid you in correcting the distortion Correcting Keystone DistortionsPress the Keystone button As illustrated on the right, a dialog will appearFreezing the Screen Using the Magnify FeatureSignal Searching Selecting the Aspect RatioTemporarily Blanking the Screen Press Buttons to adjust the level Using the Menu FunctionsSelect a menu using Buttons Then press Or Enter button Select an item using Buttons, then press Or Enter buttonOperating the PC Screen Available Functions Remote Control OperationHigh Voltage High Temperature High Pressure LampDo not use the projector with the lamp cover removed Replacing the lamp Caring for the air filter AIR FilterReplacing the air filter Caring for the lens Caring for the cabinet and remote control transmitterOther Care Caring for the inside of the projectorFor Technical see the end of this manual Multifunctional Settings Main MenuMain Menu PICTURE2 Menu Picture 1 MenuPicture 2 Menu PICTURE1 MenuVideo Input MenuInput Menu AutoStart UP Screen MenuScreen Menu BlankWhisper Option MenuOption Menu Auto OFFRelated Messages Power Lamp Temp Regarding the Indicator LampsVol.2-6 Phenomena That May Easily Be Mistaken for Machine DefectsVol.2-2 Vol.2-3Unit mm SpecificationsDimension Diagram SpecificationWarranty and AFTER-SERVICE Sub 15-pin Shrink Signal Connector PIN AssignmentSignal Terminal Specification RGB in 1/2Resolution FH kHz FV Hz Rating Signal mode Display mode Example of Computer SignalInitial SET Signals USB Mouse Connection to the Mouse ControlADB Mouse Serial MouseProtocol Command dataConsist of header 7 bytes + command data 6 bytes RS-232C CommunicationIncreasing the projector setting value Increment command Requesting projector status Get commandChanging the projector settings Set command Using the projector default settings Reset Command日本語 Command data chartBe EF BA D2 Be EF FD D3 Be EF Ntsc PAL Regulatory Notices Hitachi France Hitachi Europe GmbHHitachi Sales Europe GmbH Hitachi Business Systems Nordic